- 您現在的位置：買賣IC網 > PDF目錄179919 > LTC4263CDE#PBF (LINEAR TECHNOLOGY CORP) Single IEEE 802.3af Compliant PSE Controller with Internal Switch; Package: DFN; No of Pins: 14; Temperature Range: 0°C to +70°C PDF資料下載
參數資料
| 型號： | LTC4263CDE#PBF |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | Single IEEE 802.3af Compliant PSE Controller with Internal Switch; Package: DFN; No of Pins: 14; Temperature Range: 0°C to +70°C |
| 中文描述： | SPECIALTY MICROPROCESSOR CIRCUIT, PDSO14 |
| 封裝： | 4 X 3 MM, LEAD FREE, PLASTIC, MO-229WGED-3, DFN-14 |
| 文件頁數： | 11/24頁 |
| 文件大小： | 349K |
| 代理商： | LTC4263CDE#PBF |
LTC4263
19
4263fe
APPLICATIONS INFORMATION
Fuse
While the LTC4263 does not require a fuse for proper
operation or for compliance with IEEE 802.3af, some
safety requirements state that the output current must be
limited to less than 2A in less than 60 seconds if any one
component fails or is shorted. Since the LTC4263 is the
primary current limiter, its failure could result in excess
current to the port. To meet these safety requirements, a
fuse can be placed in the positive leg of the port. The fuse
must be large enough that it will pass at least 450mA when
derated for high temperature but small enough that it will
fuse at less than 2A at cold temperature. This requirement
can usually be satised with a 1A fuse or PTC. Placing the
fuse between the RJ-45 connector and the LTC4263 and
its associated circuitry provides additional protection for
this circuitry. Consult a safety requirements expert for the
application specic requirements.
Power Supply
Poor regulation on the 48V supply can lead to
noncompliance. The IEEE specication requires a PSE
output voltage between 44V and 57V. When the LTC4263
begins powering an Ethernet port, it controls the current
through the port to minimize disturbances on VSS.However,
if the VSS supply is underdamped or otherwise unstable,
its voltage could go outside of the IEEE-specied limits,
causing the PSE to be noncompliant. This scenario can be
even worse when a PD is unplugged because the current
can drop immediately to zero. In both cases the port voltage
must always stay between 44V and 57V. Beyond this, the
IEEE 802.3af specication places specic ripple, noise and
load regulation requirements on the PSE. Disturbances
on VSS can also adversely affect detection, classication
and AC disconnect sensing. For these reasons, proper
bypassing and stability of the VSS supply is important.
Another problem that can affect the VSS supply is
insufcient power, leading to the supply voltage dropping
out of the specied range. The 802.3af specication states
that if a PSE powers a PD it must be able to provide the
maximum power level requested by the PD based on
the PD’s classication. The specication does allow a
PSE to choose not to power a port, typically because the
PD requires more power than the PSE has available to
deliver. If a PSE is built with a VSS supply not capable of
delivering full power to all ports, it is recommended to
use the LTC4263 power management feature to prevent
ports from being turned on when there is insufcient
power. Because the specication also requires the PSE
to supply an inrush current of 400mA at up to a 5% duty
cycle, the VSS supply capability should be at least a few
percent higher than the maximum total power the PSE
needs to supply to the PDs.
Isolation
The IEEE 802.3af standard requires Ethernet ports to be
electrically isolated from all other conductors that are
user accessible. This includes the metal chassis, other
connectors, and the AC power line. Environment A isolation
is the most common and applies to wiring within a single
building serviced by a single AC power system. For this
type of application, the PSE isolation requirement can be
met with the use of a single, isolated 48V supply powering
several LTC4263 ports. Environment B, the stricter isolation
requirement, is for networks that cross an AC power
distribution boundary. In this case, electrical isolation
must be maintained between each port in the PSE. The
LTC4263 can be used to build a multi-port Environment B
PSE by powering each LTC4263 from a separate, isolated
48V supply. In all PSE applications, there should be no
user accessible connections to the LTC4263 other than
the RJ-45 port.
相關PDF資料 |
PDF描述 |
|---|---|
| LTE-4218 | 5 mm, 1 ELEMENT, INFRARED LED, 940 nm |
| LTF5022T-3R3N2R5 | 1 ELEMENT, 3.3 uH, FERRITE-CORE, GENERAL PURPOSE INDUCTOR, SMD |
| LTFD101-3 | SPECIAL SWITCH-DISCONNECT SWITCH, MOMENTARY, 125A, 80VDC, PANEL MOUNT |
| LTFD101-4 | SPECIAL SWITCH-DISCONNECT SWITCH, MOMENTARY, 125A, 80VDC, PANEL MOUNT |
| LTFD101-1 | SPECIAL SWITCH-DISCONNECT SWITCH, MOMENTARY, 125A, 80VDC, PANEL MOUNT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC4263CDE-TRPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Single IEEE 802.3af Compliant PSE Controller with Internal Switch |
| LTC4263CS | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Single IEEE 802.3af Compliant PSE Controller with Internal Switch |
| LTC4263CS#PBF | 功能描述:IC IEEE 803.2AF CNTRLR 14-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF) |
| LTC4263CS#TRPBF | 功能描述:IC IEEE 803.2AF CNTRLR 14-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:100 系列:- 類型:熱插拔開關 應用:通用 內部開關:是 電流限制:可調 電源電壓:9 V ~ 13.2 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP（3x3） 包裝:管件 |
| LTC4263CS-PBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Single IEEE 802.3af Compliant PSE Controller with Internal Switch |
發布緊急采購，3分鐘左右您將得到回復。