- 您現在的位置：買賣IC網 > PDF目錄179919 > LTC4259ACGW-1#PBF (LINEAR TECHNOLOGY CORP) Quad IEEE 802.3af Power over Ethernet Controller with AC Disconnect; Package: SSOP; No of Pins: 36; Temperature Range: 0°C to +70°C PDF資料下載
參數資料
| 型號： | LTC4259ACGW-1#PBF |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 電源管理 |
| 英文描述： | Quad IEEE 802.3af Power over Ethernet Controller with AC Disconnect; Package: SSOP; No of Pins: 36; Temperature Range: 0°C to +70°C |
| 中文描述： | 4-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO36 |
| 封裝： | 0.300 INCH, LEAD FREE, PLASTIC, SSOP-36 |
| 文件頁數： | 19/32頁 |
| 文件大?。?/td> | 416K |
| 代理商： | LTC4259ACGW-1#PBF |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
LTC4259A-1
26
4259a1fa
direction. A STOP condition is not used to set up a
REPEATED START condition, for this would clear any data
already latched in. When the master has finished commu-
nicating with the slave, it issues a STOP condition. A STOP
condition is generated by transitioning SDA from low to
high while SCL is high. The bus is then free for communi-
cation with another SMBus or I2C device.
Acknowledge
The Acknowledge signal is used for handshaking between
the master and the slave. An Acknowledge (active LOW)
generated by the slave lets the master know that the latest
byte of information was received. The corresponding SCL
clock pulse is always generated by the master. The master
releases the SDA line (HIGH) during the Acknowledge
clock pulse. The slave must pull down the SDA line during
the Acknowledge clock pulse so that it remains a stable
LOW during the HIGH period of this clock pulse. When the
master is reading from a slave device, it is the master’s
responsibility to acknowledge receipt of the data byte in
the bit that follows unless the transaction is complete. In
that case the master will decline to acknowledge and issue
the STOP condition to terminate the communication.
Write Byte Protocol
The master initiates communication to the LTC4259A-1
with a START condition and a 7-bit bus address followed
by the Write Bit (Wr) = 0. If the LTC4259A-1 recognizes its
own address, it acknowledges and the master delivers the
command byte, signifying to which internal LTC4259A-1
register the master wishes to write. The LTC4259A-1 ac-
knowledges and latches the lower five bits of the com-
mand byte into its Register Address register. Only the lower
five bits of the command byte are checked by the LTC4259A-
1; the upper three bits are ignored. The master then deliv-
ers the data byte. The LTC4259A-1 acknowledges once
more and latches the data into the appropriate control
register. Finally, the master terminates the communica-
tion with a STOP condition. Upon reception of the STOP
condition, the Register Address register is cleared (see
Figure 7).
Read Byte Protocol
The master initiates communication from the LTC4259A-
1 with a START condition and the same 7-bit bus address
followed by the Write Bit (Wr) = 0. If the LTC4259A-1
recognizes its own address, it acknowledges and the
master delivers the command byte, signifying which
internal LTC4259A-1 register it wishes to read from. The
LTC4259A-1 acknowledges and latches the lower five bits
of the command byte into its Register Address register. At
this time the master sends a REPEATED START condition
and the same 7-bit bus address followed by the Read Bit
(Rd) = 1. The LTC4259A-1 acknowledges and sends the
contents of the requested register. Finally, the master
declines to acknowledge and terminates communication
with a STOP condition. Upon reception of the STOP
condition, the Register Address register is cleared (see
Figure 8).
Receive Byte Protocol
Since the LTC4259A-1 clears the Register Address regis-
ter on each STOP condition, the interrupt register (register
0) may be read with the Receive Byte Protocol as well as
with the Read Byte Protocol. In this protocol, the master
initiates communication with the LTC4259A-1 with a
START condition and a 7-bit bus address followed by the
Read Bit (Rd) = 1. The LTC4259A-1 acknowledges and
sends the contents of the interrupt register. The master
then declines to acknowledge and terminates communi-
cation with a STOP condition (see Figure 9).
Alert Response Address and the INT Pin
In a system where several LTC4259A-1s share a common
INT line, the master can use the Alert Response Address
(ARA) to determine which LTC4259A-1 initiated the
interrupt.
The master initiates the ARA procedure with a START
condition and the 7-bit ARA bus address (0001100)b
followed by the Read Bit (Rd) = 1. If an LTC4259A-1 is
asserting the INT pin, it acknowledges and sends its 7-bit
bus address (010A3A2A1A0)b and a 1 (see Figure 10).
While it is sending its address, it monitors the SDAIN pin
to see if another device is sending an address at the same
APPLICATIO S I FOR ATIO
WU
UU
相關PDF資料 |
PDF描述 |
|---|---|
| LTC4259ACGW-1#TRPBF | Quad IEEE 802.3af Power over Ethernet Controller with AC Disconnect; Package: SSOP; No of Pins: 36; Temperature Range: 0°C to +70°C |
| LTC4259AIGW-1#PBF | Quad IEEE 802.3af Power over Ethernet Controller with AC Disconnect; Package: SSOP; No of Pins: 36; Temperature Range: -40°C to +85°C |
| LTC4259AIGW-1#TRPBF | Quad IEEE 802.3af Power over Ethernet Controller with AC Disconnect; Package: SSOP; No of Pins: 36; Temperature Range: -40°C to +85°C |
| LTC4259ACGW#PBF | Quad IEEE 802.3af Power over Ethernet Controller with AC Disconnect; Package: SSOP; No of Pins: 36; Temperature Range: 0°C to +70°C |
| LTC4259ACGW#TRPBF | Quad IEEE 802.3af Power over Ethernet Controller with AC Disconnect; Package: SSOP; No of Pins: 36; Temperature Range: 0°C to +70°C |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC4259AIGW-1 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Quad IEEE 802.3af Power over Ethernet Controller with AC Disconnect |
| LTC4259AIGW-1#PBF | 功能描述:IC CTRLR POE QUAD AC DISC 36SSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:2,450 系列:- 控制器類型:SPI 總線至 I²C 總線橋接 接口:I²C，串行，SPI 電源電壓:2.4 V ~ 3.6 V 電流 - 電源:11mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-HVQFN（4x4） 包裝:托盤 配用:568-3511-ND - DEMO BOARD SPI TO I2C 其它名稱:935286452157SC18IS600IBSSC18IS600IBS-ND |
| LTC4259AIGW-1#TRPBF | 功能描述:IC CTRLR POE QUAD AC DISC 36SSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:2,450 系列:- 控制器類型:SPI 總線至 I²C 總線橋接 接口:I²C，串行，SPI 電源電壓:2.4 V ~ 3.6 V 電流 - 電源:11mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-HVQFN（4x4） 包裝:托盤 配用:568-3511-ND - DEMO BOARD SPI TO I2C 其它名稱:935286452157SC18IS600IBSSC18IS600IBS-ND |
| LTC4259CGW-ES | 制造商:LINEAR_TECH 功能描述: |
| LTC4260 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:UV, OV and Reverse Supply Protection Controller Low Operating Current: 125μA |
發布緊急采購，3分鐘左右您將得到回復。