- 您現在的位置：買賣IC網 > PDF目錄44996 > LTC4222IUH#TRPBF (LINEAR TECHNOLOGY CORP) 2-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC32 PDF資料下載
參數資料
| 型號： | LTC4222IUH#TRPBF |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 電源管理 |
| 英文描述： | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC32 |
| 封裝： | 5 X 5 MM, LEAD FREE, PLASTIC, MO-220WHHD-X, QFN-32 |
| 文件頁數： | 2/32頁 |
| 文件大?。?/td> | 280K |
| 代理商： | LTC4222IUH#TRPBF |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
LTC4222
10
4222fa
SCL: Serial Bus Clock Input. Data at the SDA pin is shifted
in or out on rising edges of SCL. This is a high impedance
pin that is generally driven by an open-collector output
from a master controller. An external pull-up resistor or
current source is required.
SDAO: (SSOP Package) Serial Bus Data Output. Open-
drain output for sending data back to the master control-
ler or acknowledging a write operation. Normally tied to
SDAI to form the SDA line. An external pull-up resistor
or current source is required. Internally tied to SDAI in
QFN package.
SDAI: (SSOP Package) Serial Bus Data Input. A high im-
pedance input for shifting in address, command or data
bits. Normally tied to SDAO to form the SDA line. Internally
tied to SDAO in QFN package.
SDA: (QFN Package) Serial Bus Data Input/Output Line.
Formed by internally tying the SDAO and SDAI lines
together. An external pull-up resistor or current source
is required.
SENSE1–, SENSE2–:
Negative Current Sense Input. Con-
nect this pin to the output of the current sense resistor. The
current limit circuit controls the corresponding GATE pin
voltage to limit the sense voltage between the SENSE+ and
SENSE– pins to the level set by the soft-start and foldback
characteristic, with a maximum of 50mV during start-up
and to 150mV independent of soft-start and foldback after
the start-up timer has expired. A circuit breaker, enabled
after start-up, trips when the sense voltage exceeds 50mV
for 20μs.
SENSE1+, SENSE2+:
(SSOP Package) Positive Current
Sense Input. Connect this pin to the input of the current
sense resistor. It must be connected to the same trace as
VDDn. Internally tied to VDDn in the QFN package.
SOURCE1, SOURCE2: N-Channel MOSFET Source and
ADC Input. Connect this pin to the source of the external
N-channel MOSFET switch for gate drive return. This pin
also serves as the ADC input to monitor output voltage.
The pin provides a return for the gate pull-down circuit.
SS: Soft-Start Input. Sets the inrush current slew rate at
start-up. Connect a 68nF capacitor to provide 5mV/ms as
the slew rate for the sense voltage in start-up. This cor-
responds to 1A/ms with a 5mΩ sense resistor. Note that
a large soft-start capacitor and a small TIMER capacitor
may result in a condition where the timer expires before
the inrush current has started. Allow an additional 2nF of
timer capacitance per 1nF of soft-start capacitor to ensure
proper start-up.
TIMER: Start-Up Timer Input. Connect a capacitor be-
tween this pin and ground to set a 12.3ms/μF duration
for start-up, after which an overcurrent fault is logged if
the inrush is still current limited. The duration of the off
time is 600ms/μF when overcurrent auto-retry is enabled,
resulting in a 1:50 duty cycle. An internal timer provides
a 100ms start-up time and 5 second auto-retry time if
this pin is tied to INTVCC. Allow an additional 2nF of timer
capacitance per 1nF of soft-start (SS) capacitor to ensure
proper start-up.
UV1, UV2: Undervoltage Comparator Input. Connect this
pin to an external resistive divider from VDD. If the volt-
age at this pin falls below 1.145V, an undervoltage fault
is detected and the GATE turns off. Pulling this pin below
0.4V resets the fault register for that channel except for
the UV fault bit. Tie to INTVCC if unused.
VDD1, VDD2: Supply Voltage Input and Positive Current
Sense Input. This pin has an undervoltage lockout threshold
of 2.43V. In the QFN package this pin is also the positive
current sense input.
PIN FUNCTIONS
相關PDF資料 |
PDF描述 |
|---|---|
| LTC4222IUH#PBF | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC32 |
| LTC4227CGN-2#TRPBF | POWER SUPPLY MANAGEMENT CKT, PDSO16 |
| LTC4227IGN-1#PBF | POWER SUPPLY MANAGEMENT CKT, PDSO16 |
| LTC4227CUFD-1#TRPBF | POWER SUPPLY MANAGEMENT CKT, PQCC20 |
| LTC4227CUFD-2#TRPBF | POWER SUPPLY MANAGEMENT CKT, PQCC20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC4223 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual Ideal Diode and Hot Swap Controller |
| LTC4223-1 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual Supply Hot Swap Controller for Advanced Mezzanine Card |
| LTC4223-2 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual Supply Hot Swap Controller for Advanced Mezzanine Card |
| LTC4223CDHD-1#PBF | 功能描述:IC CNTRLR HOT SWAP DUAL 16-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件 |
| LTC4223CDHD-1#TRPBF | 功能描述:IC CNTRLR HOT SWAP DUAL 16-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。