- 您現在的位置：買賣IC網 > PDF目錄44996 > LTC4222CG#PBF (LINEAR TECHNOLOGY CORP) 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO36 PDF資料下載
參數資料
| 型號： | LTC4222CG#PBF |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 電源管理 |
| 英文描述： | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO36 |
| 封裝： | 5.30 MM, LEAD FREE, PLASTIC, SSOP-36 |
| 文件頁數： | 4/32頁 |
| 文件大?。?/td> | 280K |
| 代理商： | LTC4222CG#PBF |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
LTC4222
12
4222fa
OPERATION
The LTC4222 is designed to turn two supply voltages
on and off in a controlled manner, allowing boards to be
safely inserted or removed from a live backplane. During
normal operation, the charge pump and gate drivers turn
on external N-channel MOSFET gates to pass power to
the loads. The gate driver circuits use a charge pump that
derives its power from the VDD1 or VDD2 pin, whichever is
higher. Also included in the gate driver circuits are internal
6.5V GATE-to-SOURCE clamps to protect the oxide of
logic-level MOSFETs. During start-up the inrush currents
are tightly controlled by using current limit foldback, soft-
start dI/dt limiting and output dI/dt limiting. The LTC4222
is capable of controlling both channels independently, or
coupling control signals so that both channels start up
and turn off together.
The current sense (CS) ampliers monitor the load cur-
rents using the difference between the SENSE+ (VDD for
QFN) and SENSE– pin voltages. A CS amplier limits the
current in the load by pulling back on the GATE-to-SOURCE
voltage in an active control loop when the sense voltage
exceeds the commanded value. The CS ampliers require
20μA input bias current from both the SENSE+ and the
SENSE– pins.
A short circuit on an output to ground results in excessive
power dissipation during active current limiting. To limit this
power, the corresponding CS amplier regulates the voltage
between the SENSE+ and SENSE– pins at 150mV.
If an overcurrent condition persists, the internal circuit
breaker (CB) registers a fault when the sense voltage
exceeds 50mV for more than 20μs. This indicates to
the logic that it is time to turn off the GATE to prevent
overheating. At this point the TIMER capacitor starts to
discharge with the 2μA current source until the voltage
drops below 0.2V (comparator TM1) which tells the logic
that the pass transistor has cooled and it is safe to turn
on again if overcurrent auto-retry is enabled. If the TIMER
pin is tied to INTVCC, the cool-down time defaults to
5 seconds using an internal system timer.
The output voltages are monitored using the FB resistive
divider and the power good (PG) comparators to determine
when output voltages are acceptable for the loads. The
power good conditions are signaled by the GPIO1 and
GPIO2 pins using open-drain pull-down transistors. The
GPIO pins may also be independently congured to signal
power bad, or as general purpose inputs (GP comparators),
or general purpose open-drain outputs.
The Functional Diagram shows the monitoring blocks of
the LTC4222. The group of comparators on the left side
includes the undervoltage (UV), overvoltage (OV), reset
(RST), enable (EN) and on (ON) comparators for chan-
nel 1 or 2. These comparators determine if the external
conditions are valid prior to turning on their correspond-
ing GATE. The two undervoltage lockout circuits, UVLO1
and UVLO2, validate the input supplies and the internally
generated 3.3V supply, INTVCC. UVLO2 also generates
the power-up initialization to the logic circuits as INTVCC
crosses this rising threshold.
The CONFIG pin is used to select the desired start-up
behavior of the LTC4222. When the CONFIG pin is low,
both channels will start up and turn off simultaneously
and a fault on either channel will result in both channels
turning off, or prevent both channels from starting up.
tSU, DAT
tSU,STO
tSU,STA
tBUF
tHD,STA
tSP
tHD,DATO,
tHD,DATI
tHD,STA
START
CONDITION
STOP
CONDITION
REPEATED START
CONDITION
START
CONDITION
4222 TD01
SDAI/SDAO
SCL
TIMING DIAGRAM
相關PDF資料 |
PDF描述 |
|---|---|
| LTC4222CG#TRPBF | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO36 |
| LTC4222IUH#TRPBF | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC32 |
| LTC4222IUH#PBF | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC32 |
| LTC4227CGN-2#TRPBF | POWER SUPPLY MANAGEMENT CKT, PDSO16 |
| LTC4227IGN-1#PBF | POWER SUPPLY MANAGEMENT CKT, PDSO16 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC4222CG-TRPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual Hot Swap Controller with I2C Compatible Monitoring |
| LTC4222CUH#PBF | 功能描述:IC CTRLR DUAL HOT SWAP 32-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF) |
| LTC4222CUH#TRPBF | 功能描述:IC CTRLR DUAL HOT SWAP 32-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF) |
| LTC4222CUH-PBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual Hot Swap Controller with I2C Compatible Monitoring |
| LTC4222CUH-TRPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual Hot Swap Controller with I2C Compatible Monitoring |
發布緊急采購，3分鐘左右您將得到回復。