- 您現在的位置：買賣IC網 > PDF目錄44996 > LTC4110EUHF (LINEAR TECHNOLOGY CORP) 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC38 PDF資料下載
參數資料
| 型號： | LTC4110EUHF |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 電源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC38 |
| 封裝： | 5 X 7 MM, 0.75 MM HEIGHT, PLASTIC, MO-220WHKD, QFN-38 |
| 文件頁數： | 16/52頁 |
| 文件大小： | 450K |
| 代理商： | LTC4110EUHF |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
LTC4110
23
4110fb
REGISTER RESET STATE
The SHDN pin will reset all logic registers when taken high,
but only if DCIN is present as determined by DCDIV > VAC
+ VACH and DCIN above UVLO. Micropower shutdown
state will not be entered, but the LTC4110 will be idle and
not able to enter charge or calibration modes. If SHDN is
switched low then normal operation will resume.
While in register reset state, charge and calibration modes
are inhibited, and all registers including the backup fault bit
register are set to their default states and the internal timer
is reset. The status pin ACPb is active, but GPIO1, GPIO2
and GPIO3 are reset to their default states. The SMBus is
enabled, however, it is not able to communicate with the
LTC4110. The DCIN to DCOUT PowerPath controller is
functional and the VDD and VREF pin voltages remain.
MICROPOWER SHUTDOWN STATE
If the SHDN pin remains high when DCIN is removed as
detected by the undervoltage lockout UVLO (see VUVD),
micropower shutdown is entered, battery backup mode is
inhibited and all registers are reset. During this condition,
the level of the SHDN pin is ignored and has no effect.
OPERATION
#
Logic Event (T = True, F = False) [Notes]
Notes and/or Actions (T = True, F = False)
1
RES_OR = F & DCDIV pin = T & SHDN pin = F & CAL_FLT = F &
CAL_START = T
CAL_COMPLETE = F
(Calibration started while in Reset {Idle or Cold Power-Up})
2
RES_OR = F & DCDIV pin = T & SHDN pin = F & CAL_FLT = F &
CAL_START = T
ICHG or IPPC = Off & All Timers = Reset & CAL_COMPLETE = F
(Calibration was initiated while in any mode other than Reset.)
3
[Calibration Automatically Started]
ICAL = ON & CAL_ON = T
4VBAT < VCAL [Battery has reached Discharge]
ICAL = Off & CAL_ON = F & CAL_COMPLETE = T
(Normal Calibration Cycle)
5VBAT < VCAL [Battery is Discharged]
CAL_COMPLETE = T
(Battery is already discharged. Cancel Calibration.)
6
AlarmWarning() command is sent by Smart Battery over SMBus
with any of the following bits set to True:
OVER_TEMP_ALARM or Reserved ALARM or
TERMINATED_DISCHARGE_ALARM]
ICAL = Off & CAL_ON = F & ALARM_INHIBITED = T
(ALARM_INHIBITED bit is found in ChargeStatus())
7
CAL_RESET = T
ICAL = Off & CAL_ON = F & CAL_COMPLETE = F & CAL_FLT = F
8
Or
RES_HOT = T & RES_UR = F [See ChargeStatus()]
RES_OR = T [Bat Removed, See ChargeStatus()]
VOVP = T [Output Over-Voltage condition sensed)]
IBDT = T [Output Back Drive Current condition sensed)]
ICAL = Off & CAL_ON = F & CAL_FLT = T
9
Or
DCDIV pin = F
SHDN pin = T
VUVD = T
POR_RESET = T [See ChargeMode()]
ICAL = Off & CAL_ON = F & ALARM_INHIBITED = F &
CHARGE_INHIBITED = F
Figure 7. Calibration State Diagram
4110 F07
1
3
2
6, 9
8
(CALIBRATION FAULT)
7
CALIBRATION
RUNNING
ANY
STATE
RESUME
STATE
CALIBRATION
START
YES
NO
5 (BATTERY IS DEAD)
4
(CALIBRATION
COMPLETED)
RESET
CALIBRATION
MODE?
相關PDF資料 |
PDF描述 |
|---|---|
| LTC4151CS-2#TRPBF | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO16 |
| LTC4151HMS#TRPBF | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO10 |
| LTC4151HDD#TRPBF | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO10 |
| LTC4151HDD#PBF | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO10 |
| LTC4155EUFD#PBF | POWER SUPPLY SUPPORT CKT, PQCC28 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC4110EUHF#PBF | 功能描述:IC BATTERY BACKUP MANAGER 38-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 其它有關文件:STC3100 View All Specifications 特色產品:STC3100 - Battery Monitor IC 標準包裝:4,000 系列:- 功能:燃料，電量檢測計/監控器 電池化學:鋰離子（Li-Ion） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-MiniSO 包裝:帶卷 (TR) 其它名稱:497-10526-2 |
| LTC4110EUHF#PBF | 制造商:Linear Technology 功能描述:Battery Management IC |
| LTC4110EUHF#TRPBF | 功能描述:IC BATTERY BACKUP MANAGER 38-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
| LTC4110EUHF-PBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Battery Backup System Manager |
| LTC4110EUHF-TR | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Battery Backup System Manager |
發布緊急采購，3分鐘左右您將得到回復。