- 您現在的位置：買賣IC網 > PDF目錄44996 > LTC4098EUDC-1#PBF (LINEAR TECHNOLOGY CORP) BATTERY CHARGE CONTROLLER, 2650 kHz SWITCHING FREQ-MAX, PQCC20 PDF資料下載
參數資料
| 型號： | LTC4098EUDC-1#PBF |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | BATTERY CHARGE CONTROLLER, 2650 kHz SWITCHING FREQ-MAX, PQCC20 |
| 封裝： | 4 X 3 MM, 0.75 MM HEIGHT, LEAD FREE, PLASTIC, QFN-20 |
| 文件頁數： | 16/32頁 |
| 文件大?。?/td> | 443K |
| 代理商： | LTC4098EUDC-1#PBF |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
LTC4098/LTC4098-1
23
40981fc
is used in the compensation of the switching regulator. At
least 10μF with low ESR are required on VOUT. Additional
capacitance will improve load transient performance
and stability.
Multilayer ceramic chip capacitors typically have excep-
tional ESR performance. MLCCs combined with a tight
board layout and an unbroken ground plane will yield very
good performance and low EMI emissions.
There are several types of ceramic capacitors avail-
able each having considerably different characteristics.
For example, X7R ceramic capacitors have the best voltage
and temperature stability. X5R ceramic capacitors have
apparently higher packing density but poorer performance
over their rated voltage and temperature ranges. Y5V
ceramic capacitors have the highest packing density,
but must be used with caution, because of their extreme
nonlinear characteristic of capacitance versus voltage. The
actual in-circuit capacitance of a ceramic capacitor should
be measured with a small AC signal and DC bias as is
expected in-circuit. Many vendors specify the capacitance
versus voltage with a 1VRMS AC test signal and, as a result,
over state the capacitance that the capacitor will present
in the application. Using similar operating conditions as
the application, the user must measure or request from
the vendor the actual capacitance to determine if the
selected capacitor meets the minimum capacitance that
the application requires.
Overprogramming the Battery Charger
The USB high power specification allows for up to 2.5W
to be drawn from the USB port. The switching regulator
transforms the voltage at VBUS to just above the voltage
at BAT with high efficiency, while limiting power to less
than the amount programmed at CLPROG. The charger
should be programmed (with the PROG pin) to deliver the
maximum safe charging current without regard to the USB
specifications. If there is insufficient current available to
charge the battery at the programmed rate, it will reduce
charge current until the system load on VOUT is satisfied
and the VBUS current limit is satisfied. Programming the
charger for more current than is available will not cause
the average input current limit to be violated. It will merely
allow the battery charger to make use of all available
power to charge the battery as quickly as possible, and
with minimal power dissipation within the charger.
Overvoltage Protection
It is possible to protect both VBUS and WALL from over-
voltage damage with several additional components, as
shown in Figure 7. Schottky diodes D1 and D2 pass the
larger of V1 and V2 to R1 and OVSENS. If either V1 or V2
exceeds 6V plus VF(SCHOTTKY), OVGATE will be pulled to
GND and both the WALL and USB inputs will be protected.
Each input is protected up to the drain-source breakdown,
BVDSS, of MN1 and MN2. R1 must also be rated for the
power dissipated during maximum overvoltage. See the
Operations section for an explanation of this calculation.
Table 4 shows some N-channel MOSFETs that may be
suitable for overvoltage protection.
Table 4. Recommended OVP FETs
N-CHANNEL
MOSFET
BVDSS
RON
PACKAGE
Si2302ADS
20V
70m
Ω
SOT-23
IRLML2502
20V
35m
Ω
SOT-23
Si1472DH
30V
65m
Ω
SC70-6
NTLJS4114N
30V
20m
Ω
2mm
× 2mm
DFN
FDN372S
30V
45m
Ω
SOT-23
R1
C1
D1
V1
V2
D2
MN1
MN2
40981 F07
WALL
OVSENS
OVGATE
LTC4098/
LTC4098-1
VBUS
Figure 7. Dual Input Overvoltage Protection
APPLICATIONS INFORMATION
相關PDF資料 |
PDF描述 |
|---|---|
| LTC4110EUHF#TR | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC38 |
| LTC4110EUHF | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC38 |
| LTC4151CS-2#TRPBF | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO16 |
| LTC4151HMS#TRPBF | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO10 |
| LTC4151HDD#TRPBF | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO10 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC4098EUDC-3.6#PBF | 功能描述:IC CHARGER USB COMP 3.6V 20UTQFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:Bat-Track™, PowerPath™ 標準包裝:2,000 系列:Impedance Track™ 功能:燃料，電量檢測計/監控器 電池化學:鋰離子（Li-Ion） 電源電壓:2.4 V ~ 2.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:帶卷 (TR) 產品目錄頁面:1020 (CN2011-ZH PDF) 配用:BQ27350EVM-ND - BQ27350EVM 其它名稱:296-21665-2 |
| LTC4098EUDC-3.6#PBF | 制造商:Linear Technology 功能描述:IC, POWER MANAGER/BATTERY CHARGER, QFN20 |
| LTC4098EUDC-3.6#TRPBF | 功能描述:IC CHARGER USB COMP 3.6V 20UTQFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:Bat-Track™, PowerPath™ 標準包裝:61 系列:- 功能:電源管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:4.35 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:22-WFDFN 裸露焊盤 供應商設備封裝:22-DFN（6x3）裸露焊盤 包裝:管件 |
| LTC4099 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:I2C Controlled USB Power Manager/Charger with Overvoltage Protection |
| LTC4099EPDC#PBF | 功能描述:IC USB PWR MANAGER/CHRGR 20UTQFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:PowerPath™ 標準包裝:1 系列:- 功能:充電管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:3.75 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:剪切帶 (CT) 產品目錄頁面:669 (CN2011-ZH PDF) 其它名稱:MCP73831T-2ACI/OTCT |
發布緊急采購，3分鐘左右您將得到回復。