- 您現在的位置：買賣IC網 > PDF目錄44996 > LTC4097EDDB (LINEAR TECHNOLOGY CORP) 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO12 PDF資料下載
參數資料
| 型號： | LTC4097EDDB |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 電源管理 |
| 英文描述： | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO12 |
| 封裝： | 3 X 2 MM, 0.75 MM HEIGHT, PLASTIC, DFN-12 |
| 文件頁數： | 4/20頁 |
| 文件大小： | 219K |
| 代理商： | LTC4097EDDB |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁
LTC4097
12
4097f
Programming Charge Termination
The charge cycle terminates when the charge current
falls below the programmed termination threshold during
constant-voltage mode. This threshold is set by connect-
ing an external resistor, RITERM, from the ITERM pin to
ground.
The charge termination current threshold (ITERMINATE) is
set by the following equation:
R
V
I
V
R
ITERM
TERMINATE
ITERM
==
100
,
The termination condition is detected by using an internal
ltered comparator to monitor the ITERM pin. When the
ITERM pin voltage drops below 100mV* for longer than
tTERMINATE (typically 3ms), the charge cycle terminates,
charge current latches off and the LTC4097 enters standby
mode. When charging, transient loads on the BAT pin can
cause the ITERM pin to fall below 100mV for short periods
of time before the DC charge current has dropped below
the programmed termination current. The 3ms lter time
(tTERMINATE) on the termination comparator ensures that
transient loads of this nature do not result in premature
charge cycle termination. Once the average charge current
drops below the programmed termination threshold, the
LTC4097 terminates the charge cycle and ceases to provide
any current out of the BAT pin. In this state, any load on
the BAT pin must be supplied by the battery.
Low-Battery Charge Conditioning (Trickle Charge)
This feature ensures that deeply discharged batteries are
gradually charged before applying full charge current. If
the BAT pin voltage is below 2.9V, the LTC4097 supplies
1/10th of the full charge current to the battery until the
BAT pin rises above 2.9V. For example, if the charger is
OPERATION
*Any external sources that hold the ITERM pin above 100mV will prevent the LTC4097 from
terminating a charge cycle.
programmed to charge at 800mA from the wall adapter
input and 500mA from the USB input, the charge current
during trickle charge mode would be 80mA and 50mA,
respectively.
Automatic Recharge
In standby mode, the charger sits idle and monitors the
battery voltage using a comparator with a 1.6ms lter time
(tRECHRG). A charge cycle automatically restarts when the
battery voltage falls below 4.1V (which corresponds to
approximately 80%-90% battery capacity). This ensures
that the battery is kept at, or near, a fully charged condi-
tion and eliminates the need for periodic charge cycle
initiations. If the battery is removed from the charger, a
sawtooth waveform appears at the battery output. This
is caused by the repeated cycling between termination
and recharge events. This cycling results in pulsing at the
CHRG output; an LED connected to this pin will exhibit
a blinking pattern, indicating to the user that a battery is
not present. The frequency of the sawtooth is dependent
on the amount of output capacitance.
Status Indicators
The charge status output (CHRG) has two states: pull-down
and high impedance. The pull-down state indicates that
the LTC4097 is in a charge cycle. Once the charge cycle
has terminated or the LTC4097 is disabled, the pin state
becomes high impedance. The pull-down state is capable
of sinking up to 10mA.
The power present output (VNTC) has two states: DCIN/
USBIN voltages and high impedance. The high impedance
state indicates that sufcient voltage is not present at either
DCIN or USBIN, therefore no charging will occur. The VNTC
output is capable of sourcing up to 120mA steady state
and includes short circuit protection.
相關PDF資料 |
PDF描述 |
|---|---|
| LTC4098EUDC-1#TRPBF | BATTERY CHARGE CONTROLLER, 2650 kHz SWITCHING FREQ-MAX, PQCC20 |
| LTC4098EPDC-1#PBF | BATTERY CHARGE CONTROLLER, 2650 kHz SWITCHING FREQ-MAX, PQCC20 |
| LTC4098EUDC-1#PBF | BATTERY CHARGE CONTROLLER, 2650 kHz SWITCHING FREQ-MAX, PQCC20 |
| LTC4110EUHF#TR | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC38 |
| LTC4110EUHF | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC38 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC4097EDDB#PBF | 制造商:Linear Technology 功能描述:Battery Charger Li-Ion/Li-Pol 1200mA 4.2V 12-Pin DFN EP |
| LTC4097EDDB#TRMPBF | 功能描述:IC CHARGER LI-ION/POLY 12-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:2,000 系列:Impedance Track™ 功能:燃料，電量檢測計/監控器 電池化學:鋰離子（Li-Ion） 電源電壓:2.4 V ~ 2.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:帶卷 (TR) 產品目錄頁面:1020 (CN2011-ZH PDF) 配用:BQ27350EVM-ND - BQ27350EVM 其它名稱:296-21665-2 |
| LTC4097EDDB#TRPBF | 功能描述:IC CHARGER LI-ION/POLY 12-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:61 系列:- 功能:電源管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:4.35 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:22-WFDFN 裸露焊盤 供應商設備封裝:22-DFN（6x3）裸露焊盤 包裝:管件 |
| LTC4098 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual-Input Power Manager |
| LTC4098-1 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual-Input Power Manager |
發布緊急采購，3分鐘左右您將得到回復。