- 您現在的位置：買賣IC網 > PDF目錄2005 > LTC2245IUH#TRPBF (Linear Technology)IC ADC 14BIT 10MSPS 3V 32-QFN PDF資料下載
參數資料
| 型號： | LTC2245IUH#TRPBF |
| 廠商： | Linear Technology |
| 文件頁數： | 7/20頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 14BIT 10MSPS 3V 32-QFN |
| 標準包裝： | 2,500 |
| 位數： | 14 |
| 采樣率（每秒）： | 10M |
| 數據接口： | 并聯 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 69mW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 32-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 32-QFN 裸露焊盤（5x5） |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 1 個單端，雙極; 1 個差分，雙極 |
LTC2245
15
2245fa
APPLICATIO S I FOR ATIO
WU
UU
Output Driver Power
Separate output power and ground pins allow the output
drivers to be isolated from the analog circuitry. The power
supply for the digital output buffers, OVDD, should be tied
to the same power supply as for the logic being driven. For
example if the converter is driving a DSP powered by a 1.8V
supply, then OVDD should be tied to that same 1.8V supply.
OVDD can be powered with any voltage from 500mV up to
3.6V. OGND can be powered with any voltage from GND up
to 1V and must be less than OVDD. The logic outputs will
swing between OGND and OVDD.
Output Enable
The outputs may be disabled with the output enable pin, OE.
OE high disables all data outputs including OF. The output
Hi-Z state can be used to multiplex the data bus of several
LTC2245s.
Sleep and Nap Modes
The converter may be placed in shutdown or nap modes
to conserve power. Connecting SHDN to GND results in
normal operation. Connecting SHDN to VDD and OE to VDD
results in sleep mode, which powers down all circuitry
including the reference and typically dissipates 1mW. When
exiting sleep mode it will take milliseconds for the output
data to become valid because the reference capacitors have
to recharge and stabilize. Connecting SHDN to VDD and OE
to GND results in nap mode, which typically dissipates
15mW. In nap mode, the on-chip reference circuit is kept
on, so that recovery from nap mode is faster than that from
sleep mode, typically taking 100 clock cycles. In both sleep
and nap modes, all digital outputs are disabled and enter
the Hi-Z state.
Grounding and Bypassing
The LTC2245 requires a printed circuit board with a clean,
unbroken ground plane. A multilayer board with an inter-
nal ground plane is recommended. Layout for the printed
circuit board should ensure that digital and analog signal
lines are separated as much as possible. In particular, care
should be taken not to run any digital track alongside an
analog signal track or underneath the ADC.
High quality ceramic bypass capacitors should be used at
the VDD, OVDD, VCM, REFH, and REFL pins. Bypass capaci-
tors must be located as close to the pins as possible. Of
particular importance is the 0.1
F capacitor between
REFH and REFL. This capacitor should be placed as close
to the device as possible (1.5mm or less). A size 0402
ceramic capacitor is recommended. The large 2.2
F
capacitor between REFH and REFL can be somewhat
further away. The traces connecting the pins and bypass
capacitors must be kept short and should be made as wide
as possible.
The LTC2245 differential inputs should run parallel and
close to each other. The input traces should be as short as
possible to minimize capacitance and to minimize noise
pickup.
Heat Transfer
Most of the heat generated by the LTC2245 is transferred
from the die through the bottom-side exposed pad and
package leads onto the printed circuit board. For good
electrical and thermal performance, the exposed pad
should be soldered to a large grounded pad on the PC
board. It is critical that all ground pins are connected to a
ground plane of sufficient area.
相關PDF資料 |
PDF描述 |
|---|---|
| LTC2249IUH#TRPBF | IC ADC 14BIT 80MSPS LP 32-QFN |
| LTC2251IUH#PBF | IC ADC 10-BIT 125MSPS 3V 32-QFN |
| LTC2253IUH#TRPBF | IC ADC 12BIT 125MSPS 3V 32-QFN |
| LTC2255CUH#TRPBF | IC ADC 14BIT 125MSPS 3V 32-QFN |
| LTC2258IUJ-12#PBF | IC ADC 12BIT 65MSPS 1.8V 40-QFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC2246 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:14-Bit, 80Msps Low Power 3V ADC |
| LTC2246CUH | 制造商:Linear Technology 功能描述:ADC Single Pipelined 25Msps 14-bit Parallel 32-Pin QFN EP |
| LTC2246CUH#PBF | 功能描述:IC ADC 14BIT 25MSPS SAMPL 32-QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| LTC2246CUH#PBF | 制造商:Linear Technology 功能描述:IC, ADC, 14BIT, 25MSPS, QFN-32 |
| LTC2246CUH#TRPBF | 功能描述:IC ADC 14BIT 25MSPS SAMPL 32-QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
發布緊急采購，3分鐘左右您將得到回復。