- 您現在的位置：買賣IC網 > Datasheet目錄41 > LTC1704EGN#TRPBF (Linear Technology)IC REG DL BUCK/LINEAR 16SSOP Datasheet資料下載
參數資料
| 型號： | LTC1704EGN#TRPBF |
| 廠商： | Linear Technology |
| 文件頁數： | 18/28頁 |
| 文件大?。?/td> | 347K |
| 描述： | IC REG DL BUCK/LINEAR 16SSOP |
| 標準包裝： | 2,500 |
| 拓撲： | 降壓（降壓）（1），線性（LDO）（1） |
| 功能： | 任何功能 |
| 輸出數： | 2 |
| 頻率 - 開關： | 550kHz |
| 電壓/電流 - 輸出 1： | 控制器 |
| 電壓/電流 - 輸出 2： | 控制器 |
| 帶 LED 驅動器： | 無 |
| 帶監控器： | 無 |
| 帶序列發生器： | 無 |
| 電源電壓： | 3.15 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SSOP（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 16-SSOP |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
LTC1704/LTC1704B
18
1704bfa
APPLICATIO S I FOR ATIO
U
U
U
to keep the initial drop as QT turns on within reason
(100mV or so); its RMS current capability must be ad-
equate to withstand the 4.66A capacitor ripple current is
not the same as input RMS current at the input and the
capacitance must be large enough to maintain the input
voltage until the input supply can make up the difference.
Generally, a capacitor that meets the first two parameters
will have far more capacitance than is required to keep
capacitance-based droop under control. In our example,
we need 0.01& ESR to keep the input drop under 100mV
with a 10A current step and 5.65A
RMS
ripple current
capacity to avoid overheating the capacitor. These re-
quirements can be met with multiple low ESR tantalum or
electrolytic capacitors in parallel, or with a large mono-
lithic ceramic capacitor.
I
I
A
I
A
RMSIN
DCIN
RIPP
RMS
=
=
=
=
565
32
565 32 466
2 2
.
.
(. ) (. ) .
Tantalum capacitors are a popular choice as input capaci-
tors for LTC1704 applications, but they deserve a special
caution here. Generic tantalum capacitors have a destruc-
tive failure mechanism when they are subjected to large
RMS currents (like those seen at the input of an LTC1704).
At some random time after they are turned on, they can
blow up for no apparent reason. The capacitor manufac-
turers are aware of this and sell special surge tested
tantalum capacitors specifically designed for use with
switching regulators. When choosing a tantalum input
capacitor, make sure that it is rated to carry the RMS
current that the LTC1704 will draw. If the data sheet
doesnt give an RMS current rating, chances are the
capacitor isnt surge tested. Dont use it!
Output Bypass Capacitor Selection
The output bypass capacitor has quite different require-
ments from the input capacitor. The ripple current at the
output of a buck regulator, like the LTC1704s switcher
controller, is much lower than at the input because the
inductor current is constantly flowing at the output when-
ever the LTC1704 is operating in Continuous mode. The
primary concern at the output is capacitor ESR. Fast load
current transitions at the output will appear as voltage
across the ESR of the output bypass capacitor until the
feedback loop in the LTC1704 can change the inductor
current to match the new load current value. This ESR step
at the output is often the single largest budget item in the
load regulation calculation. As an example, our hypotheti-
cal 1.6V, 10A switcher with a 0.01& ESR output capacitor
would experience a 100mV step at the output with a 0A to
10A load stepa 6.3% output change!
Usually the solution is to parallel several capacitors at the
output. For example, to keep the transient response inside
of 3% with the previous design, wed need an output ESR
better than 0.0048&. This can be met with three 0.014&,
470礔 tantalum capacitors in parallel.
Inductor Selection
The inductor in a typical LTC1704 circuit is chosen prima-
rily for value and saturation current. The inductor value
sets the ripple current, which is commonly chosen at
around 40% of the anticipated full load current. Ripple
current is set by:
t V
L
RIPPLE
ONQB OUT
=
( )
( )
In our hypothetical 1.6V, 10A example, wed set the ripple
to 40% of 10A or 4A, and the inductor value would be:
L
t V
I
s V
A
H
with t
V
V
kHz s
ONQB OUT
RIPPLE
ONQB
=
=
?/DIV>
= ?/DIV>
=
?/DIV>
?/DIV>
?/DIV>
?/DIV>
?/DIV>
?/DIV>
= ?/DIV>
( )
( )
( )
( . )( . )
.
.
/
.
12 16
4
05
1
16
5
550 12
The inductor must not saturate at the expected peak
current. In this case, if the current limit was set to 15A, the
inductor should be rated to withstand 15A + 1/2I
RIPPLE
, or
17A without saturating.
FEEDBACK LOOP/COMPENSATION
Feedback Loop Types
In a typical LTC1704 switcher circuit, the feedback loop
consists of the modulator, the external inductor and
output capacitor, and the feedback amplifier and its com-
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1966MPMS8#TRPBF | IC RMS/DC CONV MICROPWR 8-MSOP |
| LTC1967IMS8#TRPBF | IC CONVERTER RMS-DC PREC 8MSOP |
| LTC1968IMS8#TRPBF | IC CONVERTER RMS-DC PREC 8MSOP |
| LTC3100EUD#TRPBF | IC REG BUCK/BOOST/LINEAR 16-QFN |
| LTC3104IMSE#TRPBF | IC REG DL BCK/LINEAR SYNC 16MSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1705EGN | 功能描述:IC PWR SUPPLY CONTROLLER 28SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 電源控制器，監視器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（5x5） 包裝:帶卷 (TR) |
| LTC1705EGN#PBF | 功能描述:IC PWR SUPPLY CONTROLLER 28SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電源控制器，監視器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（5x5） 包裝:帶卷 (TR) |
| LTC1705EGN#TR | 功能描述:IC PWR SUPPLY CONTROLLER 28SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 電源控制器，監視器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（5x5） 包裝:帶卷 (TR) |
| LTC1705EGN#TRPBF | 功能描述:IC PWR SUPPLY CONTROLLER 28SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電源控制器，監視器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（5x5） 包裝:帶卷 (TR) |
| LTC1706CS8-19 | 功能描述:IC VID VOLTAGE PROGRAMMER 8SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 電源控制器，監視器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（5x5） 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。