參數資料
型號： LT3837IFE#TRPBF
廠商： LINEAR TECHNOLOGY CORP
元件分類： 穩壓器
英文描述： SWITCHING CONTROLLER, 110 kHz SWITCHING FREQ-MAX, PDSO16
封裝： 4.40 MM, LEAD FREE, PLASTIC, TSSOP-16
文件頁數： 3/28頁
文件大?。?/td> 247K
代理商： LT3837IFE#TRPBF
LT3837
11
3837fc
OPERATION
Minimum Output Switch On-Time (tON(MIN))
The LT3837 affects output voltage regulation via yback
pulse action. If the output switch is not turned on, there
is no yback pulse and output voltage information is
not available. This causes irregular loop response and
start-up/latch-up problems. The solution is to require the
primary switch to be on for an absolute minimum time
per each oscillator cycle. If the output load is less than
that developed under these conditions, forced continuous
operation normally occurs. See the Applications Informa-
tion section for further details.
Enable Delay (ENDLY)
The yback pulse appears when the primary side switch
shuts off. However, it takes a nite time until the transformer
primary side voltage waveform represents the output
voltage. This is partly due to rise time on the primary
side MOSFET drain node but, more importantly, is due to
transformer leakage inductance. The latter causes a voltage
spike on the primary side, not directly related to output
voltage. Some time is also required for internal settling
of the feedback amplier circuitry. In order to maintain
immunity to these phenomena, a xed delay is introduced
between the switch turn-off command and the enabling of
the feedback amplier. This is termed “enable delay.” In
certain cases where the leakage spike is not sufciently
settled by the end of the enable delay period, regulation
error may result. See the Applications Information section
for further details.
Collapse Detect
Once the feedback amplier is enabled, some mechanism
is then required to disable it. This is accomplished by a
collapse detect comparator, which compares the yback
voltage (FB referred) to a xed reference, nominally 80%
of VFB. When the yback waveform drops below this level,
the feedback amplier is disabled.
Minimum Enable Time
The feedback amplier, once enabled, stays enabled for
a xed minimum time period termed “minimum enable
time.” This prevents lockup, especially when the output
voltage is abnormally low; e.g., during start-up. The mini-
mum enable time period ensures that the VC node is able
to pump up and increase the current mode trip point to
the level where the collapse detect system exhibits proper
operation. This time is internally set.
Effects of Variable Enable Period
The feedback amplier is enabled during only a portion of
the cycle time. This can vary from the xed minimum enable
time described to a maximum of roughly the “off” switch
time minus the enable delay time. Certain parameters of
yback amp behavior are directly affected by the variable
enable period. These include effective transconductance
and VC node slew rate.
Load Compensation Theory
The LT3837 uses the yback pulse to obtain information
about the isolated output voltage. An error source is
caused by transformer secondary current ow through the
synchronous MOSFET RDS(ON)andreallifenonzeroimped-
ances of the transformer secondary and output capacitor.
This was represented previously by the expression “ISEC
(ESR + RDS(ON)).” However, it is generally more useful
to convert this expression to effective output impedance.
Because the secondary current only ows during the off
portion of the duty cycle (DC), the effective output imped-
ance equals the lumped secondary impedance divided by
OFF time DC.
Since the OFF time duty cycle is equal to 1 – DC then:
R
ESR R
DC
S OUT
DS ON
()
–
=
+
1
where:
RS(OUT) = effective supply output impedance
DC = duty cycle
RDS(ON) and ESR are as dened previously
This impedance error may be judged acceptable in less
critical applications, or if the output load current remains
relatively constant. In these cases the external FB resistive
divider is adjusted to compensate for nominal expected
error. In more demanding applications, output impedance
error is minimized by the use of the load compensation
function.
相關PDF資料
PDF描述
LT3845AMPFE#TRPBF SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDSO16
LT3845AIFE#TRPBF SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDSO16
LT3845AMPFE#PBF SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDSO16
LT3845EFE#TR SWITCHING CONTROLLER, 600 kHz SWITCHING FREQ-MAX, PDSO16
LT3956IUHE#TRPBF SWITCHING REGULATOR, PQCC36
相關代理商/技術參數
參數描述
LT383L313 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Optoelectronic
LT3844 制造商:LINER 制造商全稱:Linear Technology 功能描述:High Voltage, Current Mode Switching Regulator Controller with Programmable Operating Frequency
LT3844EFE 制造商:LINER 制造商全稱:Linear Technology 功能描述:High Voltage, Current Mode Switching Regulator Controller with Programmable Operating Frequency
LT3844EFE#PBF 功能描述:IC REG CTRLR BST INV PWM 16TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 特色產品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 標準包裝:1 系列:PowerWise® PWM 型:電壓模式 輸出數:1 頻率 - 最大:1MHz 占空比:81% 電源電壓:4.5 V ~ 18 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-5°C ~ 125°C 封裝/外殼:32-WFQFN 裸露焊盤 包裝:Digi-Reel® 產品目錄頁面:1303 (CN2011-ZH PDF) 其它名稱:LM3754SQDKR
LT3844EFE#TRPBF 功能描述:IC REG CTRLR BST INV PWM 16TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:96% 電源電壓:4 V ~ 36 V 降壓:無 升壓:是 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:24-WQFN 裸露焊盤 包裝:帶卷 (TR)
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*