- 您現在的位置：買賣IC網 > PDF目錄30767 > LT3575IFE#PBF (LINEAR TECHNOLOGY CORP) 4.2 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO16 PDF資料下載
參數資料
| 型號： | LT3575IFE#PBF |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | 4.2 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
| 封裝： | 4.40 MM, LEAD FREE, PLASTIC, TSSOP-16 |
| 文件頁數： | 22/24頁 |
| 文件大?。?/td> | 240K |
| 代理商： | LT3575IFE#PBF |
LT3575
7
3575f
OPERATION
The LT3575 is a current mode switching regulator IC
designed specically for the isolated yback topology. The
special problem normally encountered in such circuits is
that information relating to the output voltage on the isolated
secondarysideofthetransformermustbecommunicatedto
the primary side in order to maintain regulation. Historically,
this has been done with optoisolators or extra transformer
windings. Optoisolator circuits waste output power and
the extra components increase the cost and physical size
of the power supply. Optoisolators can also exhibit trouble
due to limited dynamic response, nonlinearity, unit-to-unit
variation and aging over life. Circuits employing extra
transformer windings also exhibit deciencies. Using an
extra winding adds to the transformer’s physical size and
cost, and dynamic response is often mediocre.
The LT3575 derives its information about the isolated
output voltage by examining the primary side yback
pulse waveform. In this manner, no optoisolator nor extra
transformer winding is required for regulation. The output
voltage is easily programmed with two resistors. Since this
IC operates in boundary control mode, the output voltage is
calculated from the switch pin when the secondary current
is almost zero. This method improves load regulation
without external resistors and capacitors.
The Block Diagram shows an overall view of the system.
Many of the blocks are similar to those found in traditional
switching regulators including: internal bias regulator,
oscillator, logic, current amplier and comparator, driver,
and output switch. The novel sections include a special
yback error amplier and a temperature compensation
circuit. In addition, the logic system contains additional
logic for boundary mode operation, and the sampling
error amplier.
The LT3575 features a boundary mode control method,
wherethepartoperatesattheboundarybetweencontinuous
conduction mode and discontinuous conduction mode. The
VC pin controls the current level just as it does in normal
current mode operation, but instead of turning the switch
on at the start of the oscillator period, the part detects
when the secondary side winding current is zero.
Boundary Mode Operation
Boundary mode is a variable frequency, current-mode
switching scheme. The switch turns on and the inductor
current increases until a VC pin controlled current limit. The
voltage on the SW pin rises to the output voltage divided
by the secondary-to-primary transformer turns ratio plus
the input voltage. When the secondary current through
the diode falls to zero, the SW pin voltage falls below VIN.
A discontinuous conduction mode (DCM) comparator
detects this event and turns the switch back on.
Boundary mode returns the secondary current to zero
every cycle, so the parasitic resistive voltage drops do not
cause load regulation errors. Boundary mode also allows
the use of a smaller transformer compared to continuous
conduction mode and no subharmonic oscillation.
At low output currents the LT3575 delays turning on the
switch, and thus operates in discontinuous mode. Unlike
a traditional yback converter, the switch has to turn on
to update the output voltage information. Below 0.6V on
the VC pin, the current comparator level decreases to
its minimum value, and the internal oscillator frequency
decreases in frequency. With the decrease of the internal
oscillator, the part starts to operate in DCM. The output
current is able to decrease while still allowing a minimum
switch off-time for the error amp sampling circuitry. The
typical minimum internal oscillator frequency with VC
equal to 0V is 40kHz.
相關PDF資料 |
PDF描述 |
|---|---|
| LT3575EFE#PBF | 4.2 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
| LT3585EDDB-1#PBF | 0.65 A BATTERY CHARGE CONTROLLER, PDSO10 |
| LT3585EDDB-2#PBF | 0.95 A BATTERY CHARGE CONTROLLER, PDSO10 |
| LT3641EUFD#PBF | 3.4 A DUAL SWITCHING CONTROLLER, 2350 kHz SWITCHING FREQ-MAX, PQCC28 |
| LT3641IUFD#TRPBF | 3.4 A DUAL SWITCHING CONTROLLER, 2350 kHz SWITCHING FREQ-MAX, PQCC28 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT3579 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:6A Boost/Inverting DC/DC Converter with Fault Protection |
| LT3579-1 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:6A Boost/Inverting DC/DC Converter with Fault Protection |
| LT3579EFE#PBF | 功能描述:IC REG MULTI CONFIG SYNC 20TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:250 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V 輸入電壓:2.05 V ~ 6 V PWM 型:電壓模式 頻率 - 開關:2MHz 電流 - 輸出:500mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:6-UFDFN 包裝:帶卷 (TR) 供應商設備封裝:6-SON（1.45x1） 產品目錄頁面:1032 (CN2011-ZH PDF) 其它名稱:296-25628-2 |
| LT3579EFE#TRPBF | 功能描述:IC REG MULTI CONFIG SYNC 20TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:20 系列:SIMPLE SWITCHER® 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:12V 輸入電壓:4 V ~ 60 V PWM 型:電壓模式 頻率 - 開關:52kHz 電流 - 輸出:1A 同步整流器:無 工作溫度:-40°C ~ 125°C 安裝類型:通孔 封裝/外殼:16-DIP（0.300"，7.62mm） 包裝:管件 供應商設備封裝:16-DIP 其它名稱:*LM2575HVN-12LM2575HVN-12 |
| LT3579EFE-1#PBF | 功能描述:IC REG MULTI CONFIG SYNC 20TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:250 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V 輸入電壓:2.05 V ~ 6 V PWM 型:電壓模式 頻率 - 開關:2MHz 電流 - 輸出:500mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:6-UFDFN 包裝:帶卷 (TR) 供應商設備封裝:6-SON（1.45x1） 產品目錄頁面:1032 (CN2011-ZH PDF) 其它名稱:296-25628-2 |
發布緊急采購，3分鐘左右您將得到回復。