- 您現在的位置：買賣IC網 > PDF目錄30767 > LT3575IFE#PBF (LINEAR TECHNOLOGY CORP) 4.2 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO16 PDF資料下載
參數資料
| 型號： | LT3575IFE#PBF |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | 4.2 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
| 封裝： | 4.40 MM, LEAD FREE, PLASTIC, TSSOP-16 |
| 文件頁數： | 20/24頁 |
| 文件大小： | 240K |
| 代理商： | LT3575IFE#PBF |
LT3575
5
3575f
PIN FUNCTIONS
NC (Pins 1, 15, 16): No Connect Pins. Can be left open
or connected to any ground plane.
VIN (Pin 2): Input Voltage. This pin supplies current to
the internal start-up circuitry and as a reference voltage
for the DCM comparator and feedback circuitry. This pin
must be locally bypassed with a capacitor.
SW (Pins 3, 4): Collector Node of the Output Switch. This
pin has large currents owing through it. Keep the traces to
the switching components as short as possible to minimize
electromagnetic radiation and voltage spikes.
BIAS (Pin 5): Bias Voltage. This pin supplies current to the
switch driver and internal circuitry of the LT3575. This pin
must be locally bypassed with a capacitor. This pin may
also be connected to VIN if a third winding is not used and if
VIN≤15V.Ifathirdwindingisused,theBIASvoltageshould
be lower than the input voltage for proper operation.
SHDN/UVLO (Pin 6): Shutdown/Undervoltage Lockout.
A resistor divider connected to VIN is tied to this pin to
program the minimum input voltage at which the LT3575
will operate. At a voltage below ~0.7V, the part draws no
quiescent current. When below 1.22V and above ~0.7V,
the part will draw 7μA of current, but internal circuitry will
remain off. Above 1.22V, the internal circuitry will start
and a 7μA current will be fed into the SS pin. When this
pin falls below 1.22V, 2.8μA will be pulled from the pin to
provide programmable hysteresis for UVLO.
SS (Pin 7): Soft-Start Pin. Place a soft-start capacitor
here to limit start-up inrush current and output voltage
ramp rate. Switching starts when the voltage at this pin
reaches ~0.7V.
RILIM (Pin8):MaximumCurrentLimitAdjustPin.Aresistor
should be tied to this pin to ground to set the current
limit. Use a 10k resistor for the full current capabilities
of the switch.
VC (Pin 9): Compensation Pin for Internal Error Amplier.
Connect a series RC from this pin to ground to compensate
the switching regulator. A 100pF capacitor in parallel helps
eliminate noise.
RFB (Pin 10): Input Pin for External Feedback Resistor. This
pin is connected to the transformer primary (VSW). The
ratio of this resistor to the RREF resistor, times the internal
bandgap reference, determines the output voltage (plus
the effect of any non-unity transformer turns ratio). The
average current through this resistor during the yback
period should be approximately 200μA. For nonisolated
applications, this pin should be connected to VIN.
RREF (Pin 11): Input Pin for External Ground-Referred
Reference Resistor. This resistor should be in the range of
6k, but for convenience, need not be precisely this value.
For nonisolated applications, a traditional resistor voltage
divider may be connected to this pin.
TC (Pin 12): Output Voltage Temperature Compensation.
Connect a resistor to ground to produce a current
proportional to absolute temperature to be sourced into
the RREF node. ITC = 0.55V/RTC.
TEST (Pin 13): This pin is used for testing purposes only
and must be connected to ground for the part to operate
properly.
GND (Pin 14, Exposed Pad Pin 17): Ground. The exposed
pad of the package provides both electrical contact to
ground and good thermal contact to the printed circuit
board. The exposed pad must be soldered to the circuit
board for proper operation and should be well connected
with many vias to an internal ground plane.
相關PDF資料 |
PDF描述 |
|---|---|
| LT3575EFE#PBF | 4.2 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
| LT3585EDDB-1#PBF | 0.65 A BATTERY CHARGE CONTROLLER, PDSO10 |
| LT3585EDDB-2#PBF | 0.95 A BATTERY CHARGE CONTROLLER, PDSO10 |
| LT3641EUFD#PBF | 3.4 A DUAL SWITCHING CONTROLLER, 2350 kHz SWITCHING FREQ-MAX, PQCC28 |
| LT3641IUFD#TRPBF | 3.4 A DUAL SWITCHING CONTROLLER, 2350 kHz SWITCHING FREQ-MAX, PQCC28 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT3579 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:6A Boost/Inverting DC/DC Converter with Fault Protection |
| LT3579-1 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:6A Boost/Inverting DC/DC Converter with Fault Protection |
| LT3579EFE#PBF | 功能描述:IC REG MULTI CONFIG SYNC 20TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:250 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V 輸入電壓:2.05 V ~ 6 V PWM 型:電壓模式 頻率 - 開關:2MHz 電流 - 輸出:500mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:6-UFDFN 包裝:帶卷 (TR) 供應商設備封裝:6-SON（1.45x1） 產品目錄頁面:1032 (CN2011-ZH PDF) 其它名稱:296-25628-2 |
| LT3579EFE#TRPBF | 功能描述:IC REG MULTI CONFIG SYNC 20TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:20 系列:SIMPLE SWITCHER® 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:12V 輸入電壓:4 V ~ 60 V PWM 型:電壓模式 頻率 - 開關:52kHz 電流 - 輸出:1A 同步整流器:無 工作溫度:-40°C ~ 125°C 安裝類型:通孔 封裝/外殼:16-DIP（0.300"，7.62mm） 包裝:管件 供應商設備封裝:16-DIP 其它名稱:*LM2575HVN-12LM2575HVN-12 |
| LT3579EFE-1#PBF | 功能描述:IC REG MULTI CONFIG SYNC 20TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:250 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V 輸入電壓:2.05 V ~ 6 V PWM 型:電壓模式 頻率 - 開關:2MHz 電流 - 輸出:500mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:6-UFDFN 包裝:帶卷 (TR) 供應商設備封裝:6-SON（1.45x1） 產品目錄頁面:1032 (CN2011-ZH PDF) 其它名稱:296-25628-2 |
發布緊急采購，3分鐘左右您將得到回復。