參數資料
型號： LT1941EFE
廠商： LINEAR TECHNOLOGY CORP
元件分類： 穩壓器
英文描述： Triple Monolithic Switching Regulator
中文描述： 6 A SWITCHING REGULATOR, 1350 kHz SWITCHING FREQ-MAX, PDSO28
封裝： 4.40 MM, PLASTIC, TSSOP-28
文件頁數： 13/24頁
文件大?。?/td> 336K
代理商： LT1941EFE
13
LT1941
1941f
APPLICATIOU
Boost Pin Considerations
The capacitor and diode tied to the BOOST pin generate a
voltage that is higher than the input voltage. In most
cases, a 0.18
μ
F capacitor and fast switching diode (such
as the CMDSH-3 or MMSD914LT1) will work well. Fig-
ure3 shows two ways to arrange the boost circuit. The
BOOST pin must be more than 2.5V above the SW pin for
full efficiency. For outputs of 3.3V and higher, the stan-
dard circuit (Figure 3a) is best. For outputs between 2.8V
and 3.3V, use a small Schottky diode (such as the
BAT-54). For lower output voltages, the boost diode can
be tied to the input (Figure 3b). The circuit in Figure 3a is
more efficient because the boost pin current comes from
a lower voltage source. Finally, as shown in Figure 3c, the
anode of the boost diode can be tied to another source that
is at least 3V. For example, if you are generating 3.3V and
1.8V and the 3.3V is on whenever the 1.8V is on, the 1.8V
boost diode can be connected to the 3.3V output. In any
case, be sure that the maximum voltage at the BOOST pin
is less than 35V and the voltage difference between the
BOOST and SW pins is less than 25V.
The boost circuit can also run directly from a DC voltage
that is higher than the input voltage by more than 2.5V +
V
F
, as in Figure 3d. The diode prevents damage to the
W
U
U
LT1941 in case V
IN2
is held low while V
IN
is present. The
circuit saves several components (both BOOST pins can
be tied to D2). However, efficiency may be lower and
dissipation in the LT1941 may be higher. Also, if V
IN2
is
absent the LT1941 will still attempt to regulate the output,
but will do so with low efficiency and high dissipation
because the switch will not be able to saturate, dropping
1.5 to 2V in conduction.
The minimum operating voltage of an LT1941 application
is limited by the undervoltage lockout (3.5V) and by the
maximum duty cycle. The boost circuit also limits the
minimum input voltage for proper start-up. If the input
voltage ramps slowly, or the LT1941 turns on when the
output is already in regulation, the boost capacitor may not
be fully charged. Because the boost capacitor charges
with the energy stored in the inductor, the circuit will rely
on some minimum load current to get the boost circuit
running properly. This minimum load will depend on input
and output voltages, and on the arrangement of the boost
circuit. The minimum load current generally goes to zero
once the circuit has started. Even without an output load
current, in many cases the discharged output capacitor
will present a load to the switcher that will allow it to start.
Figure 3. Generating the Boost Voltage
V
IN
BOOST
LT1941
GND
SW
V
IN
(3a)
D2
V
OUT
C3
V
– V
SW
V
OUT
MAX V
BOOST
V
IN
OUT
V
IN
BOOST
LT1941
GND
SW
V
IN
(3b)
D2
V
OUT
C3
V
– V
SW
V
IN
MAX V
BOOST
2V
IN
V
IN
BOOST
LT1941
GND
SW
V
IN
(3d)
1941 F03
V
OUT
MAX V
BOOST
– V
SW
V
IN2
MAX V
BOOST
V
IN2
MINIMUM VALUE FOR V
IN2 =
V
IN
+ 3V
V
>V
IN
+ 3V
D2
V
IN
BOOST
LT1941
GND
SW
V
IN
(3c)
V
OUT
V
– V
SW
V
IN2
MAX V
BOOST
V
IN2
+ V
IN
MINIMUM VALUE FOR V
IN2 =
3V
D2
V
IN2
> 3V
C3
相關PDF資料
PDF描述
LT1959C RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS
LT1959I RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS
LTC1047 Dual Micropower Chopper Stabilized Op Amp With Internal Capacitors(雙路微功耗斬波穩定運算放大器（帶內部電容）)
LTC1049 Low Power Chopper Stabilized Op Amp With Internal Capacitors(單路低功耗斬波穩定運算放大器（帶內部電容）)
LTC1064-1 Low Noise, 8th Order, Clock Sweepable Elliptic Lowpass Filter(低噪聲，８階，時鐘掃描橢圓形低通濾波器)
相關代理商/技術參數
參數描述
LT1941EFE#PBF 功能描述:IC REG MULTI CONFIG TRPL 28TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 產品培訓模塊:MIC23xxx HyperLight Load™ Regulators 標準包裝:5,000 系列:HyperLight Load® 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.8V 輸入電壓:2.7 V ~ 5.5 V PWM 型:混合物 頻率 - 開關:4MHz 電流 - 輸出:2A 同步整流器:是 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-VFDFN 裸露焊盤，8-MLF? 包裝:帶卷 (TR) 供應商設備封裝:8-MLF?（2x2） 產品目錄頁面:1094 (CN2011-ZH PDF) 其它名稱:576-3303-2
LT1941EFE#TR 功能描述:IC REG MULTI CONFIG TRPL 28TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 設計資源:Design Support Tool 標準包裝:1 系列:- 類型:升壓（升壓） 輸出類型:固定 輸出數:1 輸出電壓:3V 輸入電壓:0.75 V ~ 2 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:100mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-5 細型，TSOT-23-5 包裝:剪切帶 (CT) 供應商設備封裝:TSOT-23-5 其它名稱:AS1323-BTTT-30CT
LT1941EFE#TRPBF 功能描述:IC REG MULTI CONFIG TRPL 28TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 設計資源:Design Support Tool 標準包裝:1 系列:- 類型:升壓（升壓） 輸出類型:固定 輸出數:1 輸出電壓:3V 輸入電壓:0.75 V ~ 2 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:100mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-5 細型，TSOT-23-5 包裝:剪切帶 (CT) 供應商設備封裝:TSOT-23-5 其它名稱:AS1323-BTTT-30CT
LT1942 制造商:LINER 制造商全稱:Linear Technology 功能描述:Quad DCDC Converter for Triple Outputs TFT Supply Plus LED Driver
LT1942EUF 制造商:Linear Technology 功能描述:Conv DC-DC Quad Inv/Step Up 2.6V to 16V 24-Pin QFN EP
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*