- 您現在的位置：買賣IC網 > PDF目錄44968 > LSN-2.5/16-D12HJ-C (CD TECHNOLOGIES INC) 1-OUTPUT 40 W DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | LSN-2.5/16-D12HJ-C |
| 廠商： | CD TECHNOLOGIES INC |
| 元件分類： | 電源模塊 |
| 英文描述： | 1-OUTPUT 40 W DC-DC REG PWR SUPPLY MODULE |
| 封裝： | ROHS COMPLIANT, PACKAGE-11 |
| 文件頁數： | 10/12頁 |
| 文件大?。?/td> | 206K |
| 代理商： | LSN-2.5/16-D12HJ-C |
LSN-16A D12 Series
NON-ISOLA TED , 13-80W SIP DC/DC CONVER TERS
Thermal Considerations and Thermal Protection
The typical output-current thermal-derating curves shown below enable
designers to determine how much current they can reliably derive from each
model of the LSN D12 SIP's under known ambient-temperature and air-ow
conditions. Similarly, the curves indicate how much air ow is required to
reliably deliver a specic output current at known temperatures.
The highest temperatures in LSN D12 SIP's occur at their output inductor,
whose heat is generated primarily by I2R losses. The derating curves were
developed using thermocouples to monitor the inductor temperature and
varying the load to keep that temperature below +110°C under the assorted
conditions of air ow and air temperature. Once the temperature exceeds
+115°C (approx.), the thermal protection will disable the converter. Automatic
restart occurs after the temperature has dropped below +110°C.
All but the last two DUT's were vertical-mount models, and the direction of air
ow was parallel to the unit in the direction from pin 11 to pin 1.
As you may deduce from the derating curves and observe in the efciency
curves on the following pages, LSN D12 SIP's maintain virtually constant
efciency from half to full load, and consequently deliver very impressive
temperature performance even if operating at full load.
Lastly, when LSN D12 SIP's are installed in system boards, they are obvi-
ously subject to numerous factors and tolerances not taken into account here.
If you are attempting to extract the most current out of these units under
demanding temperature conditions, we advise you to monitor the output-
inductor temperature to ensure it remains below +110°C at all times.
Output Reverse Conduction
Many DC/DC's using synchronous rectication suffer from Output Reverse
Conduction. If those devices have a voltage applied across their output before
a voltage is applied to their input (this typically occurs when another power
supply starts before them in a power-sequenced application), they will either
fail to start or self destruct. In both cases, the cause is the "freewheeling" or
"catch" FET biasing itself on and effectively becoming a short circuit.
LSN D12 SIP DC/DC converters do not suffer from Output Reverse Conduc-
tion. They employ proprietary gate drive circuitry that makes them immune
to applied output voltages.
Voltage Margining
The LSN-T/16-D12 converter can serve as the power source for a production
test environment using voltage margining. This gives the capability to vary
the net output voltage up or down for stress and functional testing of a target
system over the expected power supply voltage range.
Voltage margining requires three external resistors and two switches – the
primary precision trim resistor and two voltage margining resistors. The
switches are typically low on-resistance FET transistors acting as switches.
Devices specically designed for analog switch applications have effective
closed resistance of a few Ohms and often have a logic gate driving them.
After installing the desired trim resistor, the constant voltage output on the
LSN-T/16-D12 may be adjusted up or down a xed amount by installing sub-
trim voltage margining resistors as shown on the attached circuit. In effect, an
additional voltage divider is switched in one leg at a time to slightly raise or
lower the output voltage. Typical FET switches are the Maxim MAX4643 and
MAX4544 families.
As with the primary trim resistor, by sure to mount these voltage margining
resistors and switches close to the converter with short leads. Be aware that
the effective output voltage is the result of all error sources including the
trim resistor accuracies and temperature coefcients. Also, the resulting trim
resistor from the equations is usually not a standard precision value therefore
you may have to parallel two resistors.
CAUTION: Switch in only one resistor at a time to invoke voltage margining.
Do not turn on both resistors simultaneously. Also, do not exceed the total
power output of the converter.
Figure 5. LSN-T/16-D12 Voltage Margining
7
相關PDF資料 |
PDF描述 |
|---|---|
| LSN-1/10-D12BJ | 1-OUTPUT 10 W DC-DC REG PWR SUPPLY MODULE |
| LSN-1.2/10-D12BH | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| LSN-1.5/10-D12 | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| LSN-2.5/10-D12H | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| LSN-1.5/10-D12J | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LSN2A | 制造商:MURATA 制造商全稱:Murata Manufacturing Co., Ltd. 功能描述:Non-isolated, DOSA-SIP, 6/10/16A Selectable-Output DC/DC Converters |
| LSN2B | 功能描述:限位開關 LIMIT SWITCH RoHS:否 制造商:Honeywell 觸點形式:SPDT 執行器:Non-Contact 電流額定值:30 mA 電壓額定值 AC: 電壓額定值 DC:3.6 V 工作力:10 g IP 等級:IP 67 NEMA 額定值:1, 4, 12, 13 端接類型:4-Pin M12 Connector 安裝:SMD/SMT |
| LSN2-T | 制造商:MURATA 制造商全稱:Murata Manufacturing Co., Ltd. 功能描述:DOSA-SIP, 30A POL DC/DC Converters |
| LSN2-T/10-C | 制造商:CANDD 制造商全稱:C&D Technologies 功能描述:Non-isolated, DOSA-SIP, 6/10/16A Selectable-Output DC/DC Converters |
| LSN2-T/10-D12 | 制造商:CANDD 制造商全稱:C&D Technologies 功能描述:Non-isolated, DOSA-SIP, 6/10/16A Selectable-Output DC/DC Converters |
發布緊急采購，3分鐘左右您將得到回復。