- 您現在的位置：買賣IC網 > PDF目錄384606 > LP55281TLX (NATIONAL SEMICONDUCTOR CORP) Quad RGB Driver PDF資料下載
參數資料
| 型號： | LP55281TLX |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 顯示驅動器 |
| 英文描述： | Quad RGB Driver |
| 中文描述： | LED DISPLAY DRIVER, PBGA36 |
| 封裝： | 3 X 3 MM, 0.60 MM HEIGHT, 0.50 MM PITCH, MICRO SMD-36 |
| 文件頁數： | 24/28頁 |
| 文件大?。?/td> | 1313K |
| 代理商： | LP55281TLX |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁
Recommended External
Components
OUTPUT CAPACITOR, C
OUT
:
The output capacitor C
directly affects the magnitude of
the output ripple voltage. In general, the higher the value of
C
, the lower the output ripple magnitude. Multilayer ce-
ramic capacitors with low ESR are the best choice. At the
lighter loads, the low ESR ceramics offer a much lower
V
ripple than the higher ESR tantalums of the same value.
At the higher loads, the ceramics offer a slightly lower V
ripple magnitude than the tantalums of the same value. How-
ever, the dv/dt of the V
ripple with the ceramics is much
lower than the tantalums under all load conditions. Capacitor
voltage rating must be sufficient, 10V or greater is recom-
mended.
Some ceramic capacitors, espesically those in small pack-
ages, exhibit a strong capacitance reduction with the in-
creased applied voltage. The capacitance value can fall to
below half of the nominal capacitance. Too low output capac-
itance will increase the noise and it can make the boost
converter unstable.
INPUT CAPACITOR, C
IN
:
The input capacitor C
directly affects the magnitude of the
input ripple voltage and to a lesser degree the V
ripple. A
higher value C
will give a lower V
ripple. Capacitor voltage
rating must be sufficient, 10V or greater is recommended.
OUTPUT DIODE, D
1
:
A Schottky diode should be used for the output diode. To
maintain high efficiency the average current rating of the
schottky diode shoulde be larger than the peak inductor cur-
rent (1A). Schottky diodes with a low forward drop and fast
switching speeds are ideal for increasing efficiency in portable
applications. Choose a reverse breakdown of the schottky
diode larger than the output voltage. Do not use ordinary rec-
tifier diodes, since slow switching speeds and long recovery
times cause the efficiency and the load regulation to suffer.
INDUCTOR, L:
The LP55281's high switching frequency enables the use of
the small surface mount inductor. A 4.7 μH shielded inductor
is suggested for 2 MHz operation, 10 μH should be used at 1
MHz. The inductor should have a saturation current rating
higher than the peak current it will experience during circuit
operation
(~1A)
. Less than 300 m
ESR is suggested for high
efficiency. Open core inductors cause flux linkage with circuit
components and interfere with the normal operation of the
circuit. This should be avoided. For high efficiency, choose an
inductor with a high frequency core material such as ferrite to
reduce the core losses. To minimize radiated noise, use a
toroid, pot core or shielded core inductor. The inductor should
be connected to the SW pin as close to the IC as possible.
Recommended inductors are LPS3015 and LPS4012 from
Coilcraft and VLF4012 from TDK.
LIST OF RECOMMENDED EXTERNAL COMPONENTS
Symbol
C
V
DD1
C
V
DD2
C
V
DDIO
C
V
DDA
C
OUT
C
IN
L
BOOST
C
VREF
C
V
DDIO
R
RGB
R
RT
D
1
C
ASE
LEDs
Symbol explanation
C between V
DD1
and GND
C between V
DD2
and GND
C between V
DDIO
and GND
C between V
DDA
and GND
C between FB and GND
Value
100
Unit
nF
Type
Ceramic, X7R/X5R
100
nF
Ceramic, X7R/X5R
100
nF
Ceramic, X7R/X5R
1
μF
Ceramic, X7R/X5R
10
μF
Ceramic, X7R/X5R
C between battery voltage and GND
10
μF
Ceramic, X7R/X5R
L between SW and VBAT at 2 MHz
4.7
μH
Shielded, low ESR, I
SAT
1A
Ceramic, X7R
C between VREF and GND
100
nF
C between V
DDIO
and GND
R between IRGB and GND
100
nF
Ceramic, X7R
8.2
k
k
V
±1%
R between IRT and GND
82
±1%
Rectifying Diode (V
f
@ maxload)
C between Audio input and ASEx
0.3
Schottky diode
100
nF
Ceramic, X7R/X5R
User defined
www.national.com
24
L
相關PDF資料 |
PDF描述 |
|---|---|
| LP5551 | PowerWise⑩ Technology Compliant Energy Management Unit |
| LP5551SQ | PowerWise⑩ Technology Compliant Energy Management Unit |
| LP5551SQX | PowerWise⑩ Technology Compliant Energy Management Unit |
| LPBC4-3 | POWR-BLOKS Distribution/Splicer Blocks and Covers |
| LPBC5-1 | POWR-BLOKS Distribution/Splicer Blocks and Covers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LP55281TLX/NOPB | 功能描述:LED照明驅動器 RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| LP-554770-2S-4M | 制造商:Alpha 3 Manufacturing 功能描述: |
| LP5550 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:PowerWise Technology Compliant Energy Management Unit |
| LP5550SQ | 功能描述:電池管理 RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| LP5550SQ/NOPB | 功能描述:電池管理 RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
發(fā)布緊急采購，3分鐘左右您將得到回復。