參數資料
型號： LP3906SQX-TKXII
廠商： NATIONAL SEMICONDUCTOR CORP
元件分類： 穩壓器
英文描述： SWITCHING REGULATOR, 2000 kHz SWITCHING FREQ-MAX, QCC24
封裝： 5 X 4 MM, 0.80 MM HEIGHT, LLP-24
文件頁數： 9/40頁
文件大小： 4200K
代理商： LP3906SQX-TKXII
tremely low power mode. Quiescent supply current during this
‘sleep’ mode is less than 30 A, which allows the part to
achieve high efficiencies under extremely light load condi-
tions. When the output drops below the ‘low’ PFM threshold,
the cycle repeats to restore the output voltage to ~1.6% above
the nominal PWM output voltage.
If the load current should increase during PFM mode (see
figure below) causing the output voltage to fall below the
‘low2’ PFM threshold, the part will automatically transition into
fixed-frequency PWM mode.
SW1, SW2 OPERATION
SW1 and SW2 have selectable output voltages ranging from
0.8V to 3.5V (typ.). Both SW1 and SW2 in the LP3906 are
I2C register controlled and are enabled by default through the
internal state machine of the LP3906 following a Power-On
event that moves the operating mode to the Active state. (see
Power On Sequence). The SW1 and SW2 output voltages
revert to default values when the power on sequence has
been completed. The default output voltage for each buck
converter is factory programmable. (See Application Notes).
SW1, SW2 can be enabled/disabled through the correspond-
ing control register.
The Modulation mode PWM/PFM is by default automatic and
depends on the load as described above in the functional de-
scription. The modulation mode can be overridden by setting
I2C bit to a logic 1 in the corresponding buck control register,
forcing the buck to operate in PWM mode regardless of the
load condition.
20197803
SHUTDOWN MODE
During shutdown the PFET switch, reference, control and
bias circuitry of the converters are turned off. The NFET
switch will be on in shutdown to discharge the output. When
the converter is enabled, soft start is activated. It is recom-
mended to disable the converter during the system power up
and under voltage conditions when the supply is less than
2.8V.
SOFT START
The soft-start feature allows the power converter to gradually
reach the initial steady state operating point, thus reducing
start-up stresses and surges. The two LP3906 buck convert-
ers have a soft-start circuit that limits in-rush current during
start-up. During start-up the switch current limit is increased
in steps. Soft start is activated only if EN goes from logic low
to logic high after VIN reaches 2.8V. Soft start is implemented
by increasing switch current limit in steps of 213 mA, 425 mA,
850 mA and 1700 mA (typ. Switch current limit). The start-up
time thereby depends on the output capacitor and load cur-
rent demanded at start-up.
LOW DROPOUT OPERATION
The LP3906 can operate at 100% duty cycle (noswitching;
PMOS switch completely on) for low drop out support of the
output voltage. In this way the output voltage will be controlled
down to the lowest possible input voltage. When the device
operates near 100% duty cycle, output voltage ripple is ap-
proximately 25 mV. The minimum input voltage needed to
support the output voltage is
V
IN, MIN = ILOAD * (RDSON, PFET + RINDUCTOR) + VOUT
— ILOAD
Load current
— RDSON, PFET
Drain to source resistance of
PFET switch in the triode region
— RINDUCTOR
Inductor resistance
FLEXIBLE POWER SEQUENCING OF MULTIPLE POWER
SUPPLIES
The LP3906 provides several options for power on sequenc-
ing. The two bucks can be individually controlled with ENSW1
and ENSW2. The two LDOs can also be individually con-
trolled with ENLDO1 and ENLDO2.
If the user desires a set power on sequence, all four enables
should be tied LOW so that the regulators don’t automatically
enable when power is supplied. The user can then program
the chip through I2C and raise EN_T from LOW to HIGH to
activate the power on sequencing.
17
www.national.com
LP3906
相關PDF資料
PDF描述
LP3906SQDJXI 2 A DUAL SWITCHING CONTROLLER, 2000 kHz SWITCHING FREQ-MAX, QCC24
LP3906SQXJXXI 2 A DUAL SWITCHING CONTROLLER, 2000 kHz SWITCHING FREQ-MAX, QCC24
LP3906SQXVPFP 2 A DUAL SWITCHING CONTROLLER, 2000 kHz SWITCHING FREQ-MAX, QCC24
LP3906SQXPPXP 2 A DUAL SWITCHING CONTROLLER, 2000 kHz SWITCHING FREQ-MAX, QCC24
LP3907SQ-JIXI 1.5 A DUAL SWITCHING CONTROLLER, 2100 kHz SWITCHING FREQ-MAX, QCC24
相關代理商/技術參數
參數描述
LP3906SQX-TKXII/NOPB 功能描述:低壓差穩壓器 - LDO RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20
LP3906SQX-VPFP/NOPB 功能描述:其他電源管理 RoHS:否 制造商:Texas Instruments 輸出電壓范圍: 輸出電流:4 mA 輸入電壓范圍:3 V to 3.6 V 輸入電流: 功率耗散: 工作溫度范圍:- 40 C to + 110 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-48 封裝:Reel
LP3907 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Dual High-Current Step-Down DC/DC and Dual Linear Regulator with I2C Compatible Interface
LP3907QSQ-JJXP/NOPB 功能描述:上下轉換器 Dual Hi-Current SD DC/DC RoHS:否 制造商:Texas Instruments 產品:Down Converters 射頻:52 MHz to 78 MHz 中頻:300 MHz LO頻率: 功率增益: P1dB: 工作電源電壓:1.8 V, 3.3 V 工作電源電流:120 mA 最大功率耗散:1 W 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PQFP-128
LP3907QSQ-JXI7/NOPB 功能描述:低壓差穩壓器 - LDO RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*