- 您現在的位置：買賣IC網 > PDF目錄384602 > LMC1982CIV (NATIONAL SEMICONDUCTOR CORP) Digitally-Controlled Stereo Tone and Volume Circuit with Two Selectable Stereo Inputs PDF資料下載
參數資料
| 型號： | LMC1982CIV |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 音頻控制 |
| 英文描述： | Digitally-Controlled Stereo Tone and Volume Circuit with Two Selectable Stereo Inputs |
| 中文描述： | 2 CHANNEL(S), TONE CONTROL CIRCUIT, PQCC28 |
| 封裝： | PLASTIC, LCC-28 |
| 文件頁數： | 8/14頁 |
| 文件大?。?/td> | 348K |
| 代理商： | LMC1982CIV |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁
General Information
(Continued)
are serially shifted from the controller to the LMC1982. This
is followed by 8 bits of function value data. Data present in
the internal shift register is latched and the instruction is
executed.
Application Information
INPUT SELECTOR
The LMC1982’s input selector and mode control are shown
in Figure 2 The input selector selects one of two stereo sig-
nal sources or a mute function with typical attenuation of
100 dB. The selected signals are then sent to a mode control
matrix. As shown in Table 1 the matrix provides normal ste-
reo or can direct either channel to both LEFT or RIGHT SE-
LECT OUTPUTs. The third matrix mode is normal stereo.
The control matrix output is buffered and appears on each
channel’s respective SELECT OUT pin (6, 23). Switching
noise is kept to a minimum when mute is selected by using
a 50 k
bias resistor.
Noise performance is optimized through the use of emitter
followers in the mode control matrix’s output. Internal 50 k
resistors are connected to each input selector pin to provide
the proper bias point for the emitter follower buffers. Each in-
ternal 50 k
bias resistor is connected to a common
half-supply (V
+
/2) source. This produces a voltage at pins 6
and 23 (SELECT OUT) that is 1.4V below V
+
/2 (typically
3.1V with V
+
= 9V). Since a DC voltage is present at the in-
put pins (4, 5, 24, and 25), input signal should beAC coupled
through a 1 μF capacitor.
The output signal at pins 6 and 23 can be used to drive ex-
teral audio processing circuits such as noise reduction
(LM1894–DNR or Dolby) or graphic equalizers (LMC835). It
is important that if any noise reduction is used it be placed
ahead of any tone controls or equalizers in the external cir-
cuit path to preserve the frequency spectrum of the selected
input signal. Otherwise, any frequency equalization could
prevent the proper operation of the noise reduction circuit. If
no external processor is used, a capacitor should be used to
couple the SELECT OUT signals directly to pins 7 and 22,
respetively.
MINIMUM LOAD IMPEDANCE
The LMC1982 employs emitter-followers to buffer the se-
lected stereo channels. The buffered signals are available at
pins 6 and 23 (SELECT OUT). The SELECT OUT buffers op-
erate with a typical bias current 1 mA.
The Electrical Specifications table lists a maximum input sig-
nal of 2.0 V
(2.5 V
) for 1% THD at the SELECT OUT
pins. This distortion level is achieved when the minimum AC
load impedance seen by the SELECT OUT pins is 2.5 k
(2.5V/1 mA). Using lower load impedances results in clipping
at lower output levels. If the load impedance is DC-coupled,
an increased quiescent current can flow. Latch-up may occur
DS011028-5
FIGURE 1. Typical Application
www.national.com
8
相關PDF資料 |
PDF描述 |
|---|---|
| LMC1983 | Digitally-Controlled Stereo Tone and Volume Circuit with Three Selectable Stereo Inputs |
| LMC1983CIN | Pushbutton Switch; Actuator Style:Rectangular; Circuitry:DPST-1NO/1NC; Switch Operation:On-(On); Contact Current Max:5A; Collar Shape:Rectangular; Features:Illuminated; Leaded Process Compatible:Yes; Mounting Type:PCB |
| LMC1983CIV | Digitally-Controlled Stereo Tone and Volume Circuit with Three Selectable Stereo Inputs |
| LMC1992 | LMC1992 Digitally-Controlled Stereo Tone and Volume Circuit with Four-Channel Input-Selector |
| LMC1992CCN | LMC1992 Digitally-Controlled Stereo Tone and Volume Circuit with Four-Channel Input-Selector |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LMC1982CIVX | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Tone/Volume/Balance Control |
| LMC1983 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Digitally-Controlled Stereo Tone and Volume Circuit with Three Selectable Stereo Inputs |
| LMC1983CIN | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| LMC1983CIV | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| LMC1983CIVX | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Tone/Volume/Balance Control |
發布緊急采購，3分鐘左右您將得到回復。