參數資料
型號: LMC1982CIN
廠商: NATIONAL SEMICONDUCTOR CORP
元件分類: 音頻控制
英文描述: Digitally-Controlled Stereo Tone and Volume Circuit with Two Selectable Stereo Inputs
中文描述: 2 CHANNEL(S), TONE CONTROL CIRCUIT, PDIP28
封裝: 0.600 INCH, PLASTIC, DIP-28
文件頁數: 9/14頁
文件大小: 348K
代理商: LMC1982CIN
Application Information
(Continued)
if the total emitter current exceeds 5 mA. Thus, maximum
output voltage can be increased and much lower distortion
levels can be achieved using load impedances of at least
25 k
.
INPUT IMPEDANCE
The input impedance of pins 4, 5, 24 and 25 is defined by in-
ternal bias resistors and is typically 50 k
.
The SELECT IN pins have an input impedance that varies
with the BASE and TREBLE control settings. The input im-
pedance is 100 k
at DC and 19 k
at 1 kHz when the con-
trols are set at 0 dB. Minimum input impedance of 30.4 k
at
DC and 16 k
at 1 kHz occurs when maximum boost is se-
lected. At 10 kHz the minimum input impedance, with the
tone controls flat, is 6.8 k
and, with the tone controls at
maximum boost, is 2.5 k
.
EXTERNAL SIGNAL PROCESSING
The SELECT OUT pins (6 and 23) enable greater system
design flexibility by providing a means to implement an ex-
ternal processing loop. This loop can be used for noise re-
duction circuits such as DNR (LM1894) or multi-band
graphic equalizers (LMC835). If both are used, it is important
to ensure that the noise reduction circuitry precede the
equalization circuits. Failure to do so results in improper op-
eration of the noise reduction circuits. The system shown in
Figure 3 utilizes the external loop to include DNR and a
multi-band equalizer.
TONE CONTROL RESPONSE
Bass and treble tone controls are included in the LMC1982.
The tone controls used just two external capacitors for each
stereo channel. Each has a corner frequency determined by
the value of C2 and C3 (see Figure 4) and internal resistors
in the feedback loop of the internal tone amplifier. The
maximum-boost or cut is determined by the data sent to the
LMC1982 (see Table 1).
The typical tone control response shown in Typical Perfor-
mance Curves were generated with C2 = C3 = 0.0082 μF
and show the response for each step. When modifying the
tone control response it is important to note that the ratio of
C3 and C2 sets the mid-frequency gain. Symmetrical tone
response is achieved when C2 = C3. However, with
C2 = 2(C3) and the tone controls set to “flat”, the frequency
response will be flat at 20 Hz and 20 kHz, and +6 dB at
1 kHz.
The frequency where a tone control begins to deviate from a
flat response is referred to as the turn-over frequency. With
C = C2 = C3, the LMC1982’s treble turn-over frequency is
nominally
DS011028-6
FIGURE 2. Input and Mode Select Circuitry
www.national.com
9
相關PDF資料
PDF描述
LMC1982CIV Digitally-Controlled Stereo Tone and Volume Circuit with Two Selectable Stereo Inputs
LMC1983 Digitally-Controlled Stereo Tone and Volume Circuit with Three Selectable Stereo Inputs
LMC1983CIN Pushbutton Switch; Actuator Style:Rectangular; Circuitry:DPST-1NO/1NC; Switch Operation:On-(On); Contact Current Max:5A; Collar Shape:Rectangular; Features:Illuminated; Leaded Process Compatible:Yes; Mounting Type:PCB
LMC1983CIV Digitally-Controlled Stereo Tone and Volume Circuit with Three Selectable Stereo Inputs
LMC1992 LMC1992 Digitally-Controlled Stereo Tone and Volume Circuit with Four-Channel Input-Selector
相關代理商/技術參數
參數描述
LMC1982CIV 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Digitally-Controlled Stereo Tone and Volume Circuit with Two Selectable Stereo Inputs
LMC1982CIVX 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Tone/Volume/Balance Control
LMC1983 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Digitally-Controlled Stereo Tone and Volume Circuit with Three Selectable Stereo Inputs
LMC1983CIN 制造商:Rochester Electronics LLC 功能描述:- Bulk
LMC1983CIV 制造商:Rochester Electronics LLC 功能描述:- Bulk