參數資料
型號: LMC1982CIN
廠商: NATIONAL SEMICONDUCTOR CORP
元件分類: 音頻控制
英文描述: Digitally-Controlled Stereo Tone and Volume Circuit with Two Selectable Stereo Inputs
中文描述: 2 CHANNEL(S), TONE CONTROL CIRCUIT, PDIP28
封裝: 0.600 INCH, PLASTIC, DIP-28
文件頁數: 6/14頁
文件大小: 348K
代理商: LMC1982CIN
Connection Diagrams
Pin Description
CLK (1)
The INTERMETAL (IM) Bus clock is applied
to the CLOCK pin. This input accepts a TTL
or CMOS level signal. The input is used to
clock the DATA signal. A data bit must be
valid on the rising clock edge.
DIGITAL INPUT
1 & 2 (2, 3)
pull-up resistor, these inputs allow a periph-
eral device to place any single-bit, active low
digital information onto the IM Bus. It is then
sent out to the controlling device through the
DATA pin. Examples of such information
could include indication of the presence of a
Second Audio Program (SAP) or an FM ste-
reo carrier.
INPUTS 1 & 2
(4, 25; 5, 24)
pairs.
SELECT OUT
(6, 23)
output. This feature allows external signal
processors such as noise reduction or
graphic equalizers to be used. This output
can typically sink 1 mA. These pins should be
capacitively coupled to pins 7 and 22, re-
spectively, if no external processor is used.
SELECT IN
(7, 22)
processor uses to return a signal to the
LMC1982. These pins should be capacitively
coupled to pins 6 and 23, respectively, if no
external processor is used.
TONE IN
(8, 21)
plifier. See the Application Information sec-
tion titled “Tone Control Response”.
TONE OUT
(9, 20)
cation Information section titled “Tone Control
Response”.
OP AMP
OUT (10, 19)
control capacitors. Internally, this output is
applied to the volume attenuators.
Internally tied high to V
+
through a 30 k
These are the LMC1982’s two stereo input
The selected INPUT signal is available at this
These are the inputs that an external signal
These are the inputs to the tone control am-
Tone control amplifier output. See the Appli-
These outputs are used with external tone
LOUDNESS
(11, 18)
The output signal on these pins is a voltage
taken from the volume attenuator’s 40 dB
tap point. An external R–C network is con-
nected to these pins.
An external R–C network is connected
across these pins. This provides left-right
channel cross-coupling and cancellation to
create an enhanced stereo channel separa-
tion effect.
The output signal from these pins drives a
stereo power amplifier. The output can typi-
cally sink 1 mA.
BYPASS (14) A 10 μF capacitor is connected between this
pin and ground to provide an AC ground for
the internal half-supply voltage reference.
GROUND (15)This pin is connected to analog ground.
V
+
(26)
This is the power supply connection. The
LMC1982 is operational with supply voltages
from 6V to 12V. This pin should be bypassed
to ground through a 1.0 μF capacitor.
ID (27)
This is the IDENTITY digital input that, when
low, signals the LMC1982 to receive, from a
controlling
device,
(40
H
–47
H
), present on the DATA line.
DATA (28)
This is the serial data input for communica-
tions sent by a controller. The controller must
have open drain outputs used with external
pull-up resistors. The data rate has a maxi-
mum frequency of 1 MHz. The LMC1982 re-
quires 16 bits of data to control or change a
function: the first 8 bits select the LMC1982
and one of eight functions. The final eight bits
set the function to a desired value. The data
must be valid on the rising edge of the
CLOCK input signal.
ENHANCED
STEREO
(12, 17)
MAIN
OUTPUT
(13, 16)
a
device
address
DS011028-2
Top View
Order Number LMC1982CIN
See NS Package Number N28B
DS011028-12
Top View
Order Number LMC1982CIV
See NS Package Number V28A
www.national.com
6
相關PDF資料
PDF描述
LMC1982CIV Digitally-Controlled Stereo Tone and Volume Circuit with Two Selectable Stereo Inputs
LMC1983 Digitally-Controlled Stereo Tone and Volume Circuit with Three Selectable Stereo Inputs
LMC1983CIN Pushbutton Switch; Actuator Style:Rectangular; Circuitry:DPST-1NO/1NC; Switch Operation:On-(On); Contact Current Max:5A; Collar Shape:Rectangular; Features:Illuminated; Leaded Process Compatible:Yes; Mounting Type:PCB
LMC1983CIV Digitally-Controlled Stereo Tone and Volume Circuit with Three Selectable Stereo Inputs
LMC1992 LMC1992 Digitally-Controlled Stereo Tone and Volume Circuit with Four-Channel Input-Selector
相關代理商/技術參數
參數描述
LMC1982CIV 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Digitally-Controlled Stereo Tone and Volume Circuit with Two Selectable Stereo Inputs
LMC1982CIVX 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Tone/Volume/Balance Control
LMC1983 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Digitally-Controlled Stereo Tone and Volume Circuit with Three Selectable Stereo Inputs
LMC1983CIN 制造商:Rochester Electronics LLC 功能描述:- Bulk
LMC1983CIV 制造商:Rochester Electronics LLC 功能描述:- Bulk