參數資料
型號： LM9073T
廠商： NATIONAL SEMICONDUCTOR CORP
元件分類： 基準電壓源/電流源
英文描述： Dual High Current Low-Dropout System Regulator
中文描述： DUAL OUTPUT, FIXED POSITIVE LDO REGULATOR, PZFM11
封裝： POWER, TO-220, 11 PIN
文件頁數： 12/18頁
文件大小： 718K
代理商： LM9073T
Application Information
(Continued)
A low to high transition is required during the watchdog timer
interval at the trigger input. If this line is ever fixed high the
timer will time-out and the system will reset.
ON/OFF Input (pin 3)
The ON/OFF Input enables both the Main and External Sup-
ply outputs. In a typical application this input is connected to
the input supply through a series resistor (nominally 22K
)
and a switch (Ignition, as an example).When the switch is
closed this input is pulled high and switches ON both regula-
tor outputs. This input is internally clamped to a 7V zener di-
ode through a series 1k
resistor. The external series resis-
tor together with an optional 0.1μF capacitor to ground
provide filtering and current limiting to withstand transients
that may appear on the input supply to maintain normal op-
eration of the system.
The switching threshold of the ON/OFF comparator has 2
Volts of hysteresis to ensure noise free control of the system.
To turn the regulators ON this input must be taken above 4V.
To turn the system OFF the ON/OFF Input must be open cir-
cuited or pulled below 2 Volts.
Keep-Alive Input (pin 9)
This CMOS logic level compatible input provides a system
with the ability to control it’s own ON/OFF sequencing. The
Keep-Alive Input is OR’ed with the ON/OFF Input so either
one can independently control the regulators.
As shown in the Operational Characteristics, a system con-
troller can take the Keep-Alive Input high at any time. If the
ON/OFF switch is opened, this high level on Keep-Alive will
keep the regulators ON and the entire system operational.
This control is useful for providing as much time as neces-
sary for a system to perform ’housekeeping’ chores such as
programming EEPROM with system information prior to
turning itself OFF (by taking the Keep-Alive Input low) and
reverting to the low quiescent current state.
Asecond use of the Keep-Alive Input can be from other mod-
ules which need information from the module powered by
LM9073. A high CMOS logic level (
>
1.25V) on this input will
power up the system as needed independent from the nor-
mal ON/OFF switch.
System Keep-Alive Operation
Figure 5 illustrates the basic concept of Keep-Alive opera-
tion. The LM9073 provides the regulated supplies to an en-
tire microcontroller based system or module including re-
mote sensors. The system is switched ON or OFF by a
switch connected to the unregulated input supply and the
ON/OFF input, pin 3. When closed the regulators turn ON
and the system is held in a reset state for the duration of the
delayed reset interval controlled by C
DELAY
.
Once normal operation of the system begins, the controller
needs to set an output line connected to the Keep-Alive in-
put, pin 9, high. The system remains in normal operation un-
til switched OFF by opening the ON/OFF switch. With
Keep-Alive high the entire system remains normally biased
and will remain operational until the Keep-Alive input is taken
low.
Transistor Q1 is shown as a means to inform the controller
that the ON/OFF switch has been opened. This high level on
an input line tells the controller that the system has been
switched OFF. This indicates the start of the Keep-Alive in-
terval. The system can perform whatever actions required to
obtain the proper OFF state before actually powering down.
These general housekeeping tasks can include putting ex-
ternal devices in the proper OFF condition and storing vari-
ous system variables in EPROM for example. With the con-
troller in command of the Keep-Alive interval these tasks can
take whatever time necessary to complete.
When completed the controller takes the Keep-Alive input to
a low level and the entire system shuts down. The LM9073
powers down to a low quiescent current mode with less than
100μA drawn from the input supply.
Figure 4. Remote ON/OFF Control
DS101296-19
L
www.national.com
12
相關PDF資料
PDF描述
LM9074 Rheostat; Series:MP; Power Rating:300W; Resistance Max:200ohm; Terminal Type:Lugs; Resistance:200ohm; Type:Rheostat
LM9074M Rheostat; Series:MP; Power Rating:300W; Resistance Max:25ohm; Terminal Type:Lugs; Leaded Process Compatible:No; Peak Reflow Compatible (260 C):No; Resistance:25ohm; Type:Rheostat
LM90 3 Degree Celcious Accurate, Remote Diode and Local Digital Temperature Sensor with Two-Wire Interface
LM90CIMM 3 Degree Celcious Accurate, Remote Diode and Local Digital Temperature Sensor with Two-Wire Interface
LM90CIMMX 3 Degree Celcious Accurate, Remote Diode and Local Digital Temperature Sensor with Two-Wire Interface
相關代理商/技術參數
參數描述
LM9073T/NOPB 功能描述:IC REG LDO 5V .7A/.1A TO-220-11 RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:1 系列:- 穩壓器拓?fù)浣Y(jié)構:正，固定式 輸出電壓:4V 輸入電壓:最高 16V 電壓 - 壓降（標準）:0.28V @ 150mA 穩壓器數量:1 電流 - 輸出:150mA 電流 - 限制（最?。?- 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:5-VFBGA 供應商設備封裝:5-uSMD 包裝:Digi-Reel® 其它名稱:LP2985AIBP-4.0DKR
LM9074 制造商:NSC 制造商全稱:National Semiconductor 功能描述:System Voltage Regulator with Keep-Alive ON/OFF
LM9074EP 制造商:TI 制造商全稱:Texas Instruments 功能描述:Enhanced Plastic System Voltage Regulator with Keep-Alive ON/OFF Control
LM9074M 功能描述:線性穩壓器 - 標準 RoHS:否 制造商:STMicroelectronics 輸出類型: 極性: 輸出電壓:1.8 V 輸出電流:150 mA 負載調節: 最大輸入電壓:5.5 V 線路調整率: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-323-5L
LM9074M/NOPB 功能描述:線性穩壓器 - 標準 RoHS:否 制造商:STMicroelectronics 輸出類型: 極性: 輸出電壓:1.8 V 輸出電流:150 mA 負載調節: 最大輸入電壓:5.5 V 線路調整率: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-323-5L
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*