- 您現在的位置：買賣IC網 > PDF目錄385477 > LM27241MTC (NATIONAL SEMICONDUCTOR CORP) Synchronous Buck Regulator Controller for Mobile Systems PDF資料下載
參數資料
| 型號： | LM27241MTC |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Synchronous Buck Regulator Controller for Mobile Systems |
| 中文描述： | SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDSO20 |
| 封裝： | PLASTIC, TSSOP-20 |
| 文件頁數： | 13/27頁 |
| 文件大?。?/td> | 1336K |
| 代理商： | LM27241MTC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
Operation Descriptions
(Continued)
As mentioned in the section ‘Forced-PWM Mode and Pulse-
skip Mode’ under startup, since the current is high until the
output capacitors have charged up, there will be no observ-
able difference in the shape of the ramp-up of the output rail
in either SKIP mode or FPWM mode. The design has thus
forced the startup waveforms to be identical irrespective of
whether the FPWM mode or the SKIP mode has been
selected.
SHUTDOWN/SOFT-SHUTDOWN
When the EN pin is driven low, the LM27241 initiates shut-
down by turning OFF both upper and lower FETs completely
(this occurs irrespective of FPWM or SKIP modes). See
Figure 6
for a typical shutdown plot and note that the LDRV
goes to zero (and stays there). Though not displayed, Power
Good also goes low within less than 100ns of the EN pin
going low (t
, see Electrical Characteristics table). There-
fore in this case, the controller is NOT waiting for the output
to actually fall out of the Power Good window before it
signals Power Not Good. When the part is shutdown with a
constant current load, the time taken for the output to decay
may be calculated using the equation V/t = i/C. For example,
there is a constant current 2A load applied at the output and
the charge stored on the output capacitor continues to dis-
charge into the load. From V/t = i/C = 2A/330μF, it can be
seen that the output voltage (say 1V) will fall to zero in about
165μs.
POWER GOOD/NOT GOOD SIGNALING
PGOOD is an open-drain output pin with an external pull-up
resistor connected to 5V. It goes high (non-conducting) when
the output is within the regulation band as determined by the
Power Good window detector stage on the feedback pin
(see Block Diagram). PGOOD goes low (conducting) when
the output falls out of this window. This signal is referred to
as Power Not Good here. A glitch filter of 7μs filters out
noise, and helps to prevent spurious PGOOD responses. So
Power Not Good is not asserted until 7μs after the output has
fallen out of the Power Good window (see
t
in
Electrical Characteristics table). With the feedback pin volt-
age rising towards regulation value, there is a 20μs delay
between the output being in regulation and the signaling of
Power Good (see
t
in Electrical Characteristics
table). Power Not Good is signaled within 100ns of the
Enable pin being pulled low (see
t
SD
in Electrical Charac-
teristics table), irrespective of the fact that the output could
still be in regulation. The Soft-start capacitor is also then
discharged as explained earlier.
FAULT AND RECOVERY
If the output falls outside the Power Good window, the
response is a ‘Power Not Good’ signal. The FET drive sig-
nals are not affected. But under a fault condition assertion,
LDRV goes high immediately turning the low-side FET ON
and discharging the output capacitors. The inductor current
will then invariably slew momentarily negative (passing from
drain to source of low-side FET), before it settles down to
zero. A fault will be detected when the output falls below the
Under-voltage threshold, or rises above the Over-voltage
threshold. From its detection to assertion, there is a 7μs
delay to help to prevent spurious responses.Afault condition
is also asserted during a loss of the VIN rail or the VDD rail.
If the Enable pin is brought low prior to this fault, a soft
shutdown will occur. To recover from a fault, either of the
following options is available:
1) Enable pin is toggled: i.e. taken low (below 0.8V), then
high again (2V to 5V). This must be done with VDD between
4.5V to 5V and VIN within normal range (5.5V to 28V).
2) VDD is brought below 1.0V and then brought back up
between 4.5V to 5V. This must be done with the Enable pin
held high (2V to 5V) and VIN within normal range (5.5V to
28V).
Recovery will initiate a Soft-start sequence (see description
under section ‘Soft-start’ above).
VIN POWER-OFF (UVLO)
The LM27241 has an internal comparator that monitors VIN.
If VIN falls to approximately 4.4V, switching ceases and both
top and bottom FETs are turned OFF. ‘Power Not Good’ has
meanwhile already been signaled and a fault condition as-
serted shortly thereafter.
20120114
CH1: LDRV, CH2: Vo, CH3: SW, CH4: I
L
(1A/div)
Output 1V
@
2A, VIN = 10V, FPWM/SKIP, L = 10μH, f = 300kHz, C
OUT
=
330μF
FIGURE 6. Shutdown
20120191
FIGURE 7. Startup Power OK
L
www.national.com
13
相關PDF資料 |
PDF描述 |
|---|---|
| LM27241MTCX | Synchronous Buck Regulator Controller for Mobile Systems |
| LM2746 | Low Voltage N-Channel MOSFET Synchronous Buck Regulator Controller |
| LM2746MXA | Low Voltage N-Channel MOSFET Synchronous Buck Regulator Controller |
| LM2746MXAX | Low Voltage N-Channel MOSFET Synchronous Buck Regulator Controller |
| LM2753SD | High Power Switched Capacitor Voltage Convertor/Flash LED Driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM27241MTC/NOPB | 功能描述:IC REG CTRLR BUCK PWM VM 20TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,000 系列:- PWM 型:電壓模式 輸出數:1 頻率 - 最大:1.5MHz 占空比:66.7% 電源電壓:4.75 V ~ 5.25 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 85°C 封裝/外殼:40-VFQFN 裸露焊盤 包裝:帶卷 (TR) |
| LM27241MTCX | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Synchronous Buck Regulator Controller for Mobile Systems |
| LM27241MTCX/NOPB | 功能描述:IC REG CTRLR BUCK PWM VM 20TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:100% 電源電壓:8.2 V ~ 30 V 降壓:無 升壓:無 回掃:是 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:0°C ~ 70°C 封裝/外殼:8-DIP（0.300"，7.62mm） 包裝:管件 產品目錄頁面:1316 (CN2011-ZH PDF) |
| LM27243A E WAF | 制造商:Texas Instruments 功能描述: |
| LM2724A | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:High Speed 3A Synchronous MOSFET Driver |
發布緊急采購，3分鐘左右您將得到回復。