- 您現在的位置：買賣IC網 > PDF目錄240278 > LM25575Q0MHX (NATIONAL SEMICONDUCTOR CORP) SWITCHING REGULATOR, PDSO16 PDF資料下載
參數資料
| 型號： | LM25575Q0MHX |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | SWITCHING REGULATOR, PDSO16 |
| 封裝： | TSSOP-16 |
| 文件頁數： | 4/22頁 |
| 文件大小： | 401K |
| 代理商： | LM25575Q0MHX |
30071108
FIGURE 6. Composition of Current Sense Signal
The sample & hold DC level illustrated in Figure 6 is derived
from a measurement of the re-circulating Schottky diode an-
ode current. The re-circulating diode anode should be con-
nected to the IS pin. The diode current flows through an
internal current sense resistor between the IS and PGND
pins. The voltage level across the sense resistor is sampled
and held just prior to the onset of the next conduction interval
of the buck switch. The diode current sensing and sample &
hold provide the DC level of the reconstructed current signal.
The positive slope inductor current ramp is emulated by an
external capacitor connected from the RAMP pin to AGND
and an internal voltage controlled current source. The ramp
current source that emulates the inductor current is a function
of the Vin and Vout voltages per the following equation:
I
RAMP = (10 x (Vin – Vout)) + 50A
Proper selection of the RAMP capacitor depends upon the
selected value of the output inductor. The value of C
RAMP can
be selected from: C
RAMP = L x 10
-5
, where L is the value of
the output inductor in Henrys. With this value, the scale factor
of the emulated current ramp will be approximately equal to
the scale factor of the DC level sample and hold (1.0 V / A).
The C
RAMP capacitor should be located very close to the de-
vice and connected directly to the pins of the IC (RAMP and
AGND).
For duty cycles greater than 50%, peak current mode control
circuits are subject to sub-harmonic oscillation. Sub-harmonic
oscillation is normally characterized by observing alternating
wide and narrow pulses at the switch node. Adding a fixed
slope voltage ramp (slope compensation) to the current sense
signal prevents this oscillation. The 50A of offset current
provided from the emulated current source adds some fixed
slope to the ramp signal. In some high output voltage, high
duty cycle applications, additional slope may be required. In
these applications, a pull-up resistor may be added between
the V
CC and RAMP pins to increase the ramp slope compen-
sation.
For V
OUT > 7.5V:
Calculate optimal slope current, I
OS = VOUT x 10A/V.
For example, at V
OUT = 10V, IOS = 100A.
Install a resistor from the RAMP pin to V
CC:
R
RAMP = VCC / (IOS - 50A)
30071145
FIGURE 7. R
RAMP to VCC for VOUT > 7.5V
www.national.com
12
LM25575Q0
相關PDF資料 |
PDF描述 |
|---|---|
| LS150-5 | 1-OUTPUT DC-DC UNREG PWR SUPPLY MODULE |
| LSM-1.8/16-D12 | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| LTC4098EUDC-3.6#TRPBF | BATTERY CHARGE CONTROLLER, PQCC20 |
| LM3351MMX/NOPB | SWITCHED CAPACITOR CONVERTER, 275 kHz SWITCHING FREQ-MAX, PDSO8 |
| LM2576HV-3.3BT-LB03 | 3.5 A SWITCHING REGULATOR, 52 kHz SWITCHING FREQ-MAX, PSFM5 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM25575Q0MHX/NOPB | 功能描述:直流/直流開關轉換器 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| LM25575-Q1 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:LM25575/LM25575-Q1 SIMPLE SWITCHER?? 42V, 1.5A Step-Down Switching Regulator |
| LM25575QMH | 制造商:TI 制造商全稱:Texas Instruments 功能描述:LM25575/LM25575-Q1 SIMPLE SWITCHER?? 42V, 1.5A Step-Down Switching Regulator |
| LM25575QMH/NOPB | 功能描述:直流/直流開關轉換器 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| LM25575QMHX | 制造商:TI 制造商全稱:Texas Instruments 功能描述:LM25575/LM25575-Q1 SIMPLE SWITCHER?? 42V, 1.5A Step-Down Switching Regulator |
發布緊急采購，3分鐘左右您將得到回復。