- 您現在的位置：買賣IC網 > PDF目錄98000 > LM25066APSQE (NATIONAL SEMICONDUCTOR CORP) POWER SUPPLY SUPPORT CKT, QCC24 PDF資料下載
參數資料
| 型號： | LM25066APSQE |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 電源管理 |
| 英文描述： | POWER SUPPLY SUPPORT CKT, QCC24 |
| 封裝： | LLP-24 |
| 文件頁數： | 29/48頁 |
| 文件大?。?/td> | 1658K |
| 代理商： | LM25066APSQE |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
TABLE 28. MFR_SPECIFIC_07 GATE MASK Definitions
Bit
NAME
Default
7
Not used, always 0
0
6
Not used, always 0
0
5
VIN UV FAULT
0
4
VIN OV FAULT
0
3
IIN/PFET FAULT
0
2
OVERTEMP FAULT
0
1
Not used, always 0
0
CIRCUIT BREAKER
FAULT
0
The IIN/PFET Fault refers to the input current fault and the
MOSFET power dissipation fault. There is no input power fault
detection, only input power warning detection.
MFR_SPECIFIC_08: ALERT_MASK (D8h)
The ALERT_MASK command is used to mask the SMBA
when a specific fault or warning has occurred. Each bit cor-
responds to one of the 14 different analog and digital faults or
warnings that would normally result in an SMBA being set.
When the corresponding bit is high, that condition will not
cause the SMBA to be asserted. If that condition occurs, the
registers where that condition is captured will still be updated
(STATUS registers, DIAGNOSTIC_WORD) and the external
MOSFET gate control will still be active (VIN_OV_FAULT,
VIN_UV_FAULT,
IIN/PFET_FAULT,
CB_FAULT,
OT_FAULT). This register is accessed with the PMBus
Read / Write Word protocol. The VIN UNDERVOLTGE
FAULT flag will default to 1 on startup. However, it will be
cleared to 0 after the first time the input voltage exceeds the
resistor programmed UVLO threshold.
TABLE 29. ALERT_MASK Definitions
BIT
NAME
DEFAULT
15
VOUT UNDERVOLTAGE WARN
0
14
IIN LIMIT Warn
0
13
VIN UNDERVOLTAGE WARN
0
12
VIN OVERVOLTAGE WARN
0
11
POWER GOOD
1
10
OVERTEMP WARN
0
9
Not Used
0
8
OVERPOWER LIMIT WARN
0
7
Not Used
0
6
EXT_MOSFET_SHORTED
0
5
VIN UNDERVOLTAGE FAULT
1
4
VIN OVERVOLTAGE FAULT
0
3
IIN/PFET FAULT
0
2
OVERTEMPERATURE FAULT
0
1
CML FAULT (Communications Fault)
0
CIRCUIT BREAKER FAULT
0
MFR_SPECIFIC_09: DEVICE_SETUP (D9h)
The DEVICE_SETUP command may be used to override pin
settings to define operation of the LM25066A under host con-
trol. This command is accessed with the PMBus read / write
byte protocol.
TABLE 30. DEVICE_SETUP Byte Format
Bit
Name
Meaning
7:5
Retry setting
111 = Unlimited retries
110 = Retry 16 times
101 = Retry 8 times
100 = Retry 4 times
011 = Retry 2 times
010 = Retry 1 time
001 = No retries
000 = Pin configured retries
4
Current limit setting
0 = Low setting (25mV)
1 = High setting (46mV)
Bit
Name
Meaning
3
CB/CL Ratio
0 = Low setting (1.8x)
1 = High setting (3.6x)
2
Current limit
Configuration
0 = Use pin settings
1 = Use SMBus settings
1
Circuit breaker
Configuration
0 = Use pin settings
1 = Use SMBus settings
0
Unused
In order to configure the Current Limit Setting via this register,
it is necessary to set the Current Limit Configuration bit (2) to
1 to enable the register to control the current limit function and
the Current Limit Setting bit (4) to select the desired setting.
Similarly, in order to control the Circuit Breaker via this regis-
ter, it is necessary to set the Circuit Breaker Configuration bit
(1) to 1 to enable the register to control the Circuit Breaker
Setting, and the Circuit Breaker / Current Limit Ratio bit (3) to
the desired value. If the respective Configuration bits are not
set, the Settings will be ignored and the pin set values used.
The Current Limit Configuration effects the coefficients used
for the Current and Power measurements and warning reg-
isters.
35
www.national.com
LM25066A
相關PDF資料 |
PDF描述 |
|---|---|
| LM2575T-012G | 3.2 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, SFM5 |
| LM2577K-12/883 | 6 A SWITCHING REGULATOR, 62 kHz SWITCHING FREQ-MAX, MBFM2 |
| LM2577KADJ/883 | 6 A SWITCHING REGULATOR, 62 kHz SWITCHING FREQ-MAX, MBCY4 |
| LM2577K-15/883 | 6 A SWITCHING REGULATOR, 62 kHz SWITCHING FREQ-MAX, MBFM2 |
| LM2633MTDX/NOPB | SWITCHING CONTROLLER, 275 kHz SWITCHING FREQ-MAX, PDSO48 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM25066APSQE/NOPB | 功能描述:熱插拔功率分布 RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| LM25066APSQX | 制造商:TI 制造商全稱:Texas Instruments 功能描述:System Power Management and Protection IC with PMBusa?￠ |
| LM25066APSQX/NOPB | 功能描述:熱插拔功率分布 RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| LM25066EVK/NOPB | 功能描述:電源管理IC開發工具 LM25066 EVAL BOARD RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| LM25066IAPSQ/NOPB | 制造商:Texas Instruments 功能描述:IC PWR MGMT/PROT PMBUS 24WQFN 制造商:Texas Instruments 功能描述:System PWR Mgmt & Protection IC |
發布緊急采購，3分鐘左右您將得到回復。