- 您現在的位置：買賣IC網 > PDF目錄358777 > LE28CV1001T-12 (Sanyo Electric Co.,Ltd.) 5015 RR 26#16 SKT RECP PDF資料下載
參數資料
| 型號： | LE28CV1001T-12 |
| 廠商： | Sanyo Electric Co.,Ltd. |
| 英文描述： | 5015 RR 26#16 SKT RECP |
| 中文描述： | 1MEG（131072字× 8位）快閃記憶體 |
| 文件頁數： | 5/14頁 |
| 文件大小： | 276K |
| 代理商： | LE28CV1001T-12 |
Toggle Bit (DQ6)
Data values of 0 and 1 are output alternately for DQ6, that is DQ6 is toggled between 0 and 1, during the internal
programming cycle. When the internal programming cycle completes this toggling is stopped and the device becomes
ready to execute the next operation. Figure 5 shows the toggle bit timing diagram and Figure 10 shows the flowchart for
this operation.
Data Protection
Hardware Data Protection
Noise and glitch protection: The LE28CV1001 does not execute write operations for WE or OE pulses that are 15 ns or
shorter.
Power (V
DD
) on and cutoff detection: The programming operation is disabled when V
DD
is 2.5 V or lower.
Write inhibit mode: Writing is disabled when OE is low and either CE is high or WE is high. Use this function to prevent
writes from occurring when the power is being turned on or off.
Software Data Protection
The LE28CV1001 implements the optional software data protection function recognized by JEDEC. This function
requires that a 3-byte load operation to be performed before a write operation data load. The 3-byte load sequence starts
a page load cycle without activating any write operation. Thus this is an optimal protection scheme for unintended write
cycles triggered by noise associated with powering the chip on or off. Note that the LE28CV1001 is shipped with the
software data protection function disabled.
The software data protection circuit is activated by executing a 3-byte byte load cycle in advance of the data sequence in
the page load cycle. (See Figure 6.) This causes the device to automatically enter data protection mode. After this, write
operations require a 3-byte byte load cycle to be executed in advance. A 6-byte write sequence is required to switch the
device out of this protection mode. Figure 7 shows the timing diagram. If a write operation is attempted in software
protection mode, all device functions are disabled for 200 μs. Figure 11 shows the flowchart for this operation.
Product Identification
The device identification code is used for recognizing the device and its manufacturer. This mode can be used by
hardware and software. The hardware operating mode is used to recognize algorithms that match the device when an
external programming unit is used. Also, user systems can recognize the product number using software product
identification mode. Figure 12 shows the flowchart for this operation. The manufacturer and device codes are the same
in both modes.
No. 5409-5/14
LE28CV1001M, T-12/15
相關PDF資料 |
PDF描述 |
|---|---|
| LE28CV1001T-15 | 5015 RR 5#12 PIN RECP |
| LE28CV1001T | 1MEG (131072 words x 8 bits) Flash Memory |
| LE28DW1621T-80T | 16 Megabit FlashBank Memory |
| LE28DW1621T | 16 Megabit FlashBank Memory |
| LE28DW8102T | 8 Megabit FlashBank Memory LE28DW8102T |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LE28CV1001T-15 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:1MEG (131072 words x 8 bits) Flash Memory |
| LE28DW1621T | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:16 Megabit FlashBank Memory |
| LE28DW1621T-80T | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:16 Megabit FlashBank Memory |
| LE28DW3215AT-80 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:EEPROM |
| LE28DW8102T | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:8 Megabit FlashBank Memory LE28DW8102T |
發布緊急采購，3分鐘左右您將得到回復。