- 您現在的位置：買賣IC網 > PDF目錄358771 > LC895196K (Sanyo Electric Co.,Ltd.) ATA-PI Compatible CD-ROM Decoder IC(ATA-PI接口兼容的CD-ROM譯碼器) PDF資料下載
參數資料
| 型號： | LC895196K |
| 廠商： | Sanyo Electric Co.,Ltd. |
| 英文描述： | ATA-PI Compatible CD-ROM Decoder IC(ATA-PI接口兼容的CD-ROM譯碼器) |
| 中文描述： | ATA的皮兼容CD - ROM解碼器IC（ATA的接口兼容的有價證券的CD - ROM譯碼器） |
| 文件頁數： | 11/12頁 |
| 文件大小： | 143K |
| 代理商： | LC895196K |
D7 to D0 (input/output)
This is the MC-side data bus. Built-in pull-up resistor.
ZINT (output)
This is the interrupt signal to the microcontroller.
3. The Buffer RAM
IO0 to IO15 (input/output)
This is the buffer DRAM data bus. Built-in pull-up resistors.
RA0 to RA8 (output)
These are the address pins for the buffer RAM.
ZRAS0 (output)
These are the RAS output pins for the buffer DRAM.
ZCAS0 and ZCAS1 (output)
This is the CAS output pin for the buffer DRAM. Normally ZCAS0 is used. When two 1M (64K
×
16 bit) DRAMS
are used, connect the ZCAS0 output to the CAS pin of each DRAM. When the 2CAS types is used, connect ZCAS0
to UCAS and connect ZCAS1 to LCAS.
ZOE (output)
The read output signal for the buffer DRAM.
ZUWE, ZLWE (output)
This is the write output signal for the buffer DRAM. This connects to various DRAM pins. When the 2CAS type is
used, connect ZLWE to the write enable signal.
4. Subcode Interface
EXCK, WFCK, SBSO, SCOR (input or output)
These are the subcode interface pins. By connecting these to the CD-DSP the subcode data is accepted by the
LC895196K and transferred to the host.
5. The CD-DSP Data
BCK, SDATA, LRCK, C2PO (input)
When connected to CD-DSP, CD-ROM data is acquired. C2PO is a pin for use by the C2 flag.
6. Other Pins
ZRESET (input)
This is the LC895196K reset pin. The LC895196K is reset when this signal is low. This signal must be kept low for
at least a period of 1 μs after power on.
XTALCK0, XTAL0
These cause oscillation at 33.8688 MHz. Frequencies from the outside may also be input into XTALCK0.
XTALCK1, XTAL1
Basically, these pins cannot oscillate. If these pins are not used, connect XTALCK1 (pin 100) to ground.
MCK (output)
This outputs the XTALCK1 and XTALCK1/2 frequencies. The output can also be turned off.
No. 5852-11/12
LC895196K
相關PDF資料 |
PDF描述 |
|---|---|
| LC895196 | ATA-PI Compatible CD-ROM Decoder IC(ATA-PI接口兼容的CD-ROM譯碼器) |
| LC895198 | CD-ROM Decoder for 32 ×ATAPI (IDE) Drives(CD-ROM譯碼器用于32倍速ATAPI (IDE)驅動) |
| LC895199K | 32 CD-ROM Decoder with ATAPI (IDE) Interface |
| LC895297 | Full CAV 20× CD-ROM Decoder with Built-in ATA-PI (IDE) Interface and CD-DSP(全CAV 20倍速CD-ROM譯碼器帶內置式ATAPI (IDE)接口和CD-DSP) |
| LC895299L | 48× Speed ATAPI (IDE) CD-ROM Decoder with On-Chip Digital Servo System(48倍速ATAPI (IDE) CD-ROM譯碼器帶片上數字伺服系統) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LC895198 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:CD-ROM Decoder for 32 x ATAPI (IDE) Drives |
| LC895199K | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:32 CD-ROM Decoder with ATAPI (IDE) Interface |
| LC895297 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Full CAV 20 x CD-ROM Decoder with Built-in ATA-PI (IDE) Interface and CD-DSP |
| LC895299L | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:48 x Speed ATAPI (IDE) CD-ROM Decoder with On-Chip Digital Servo System |
| LC895299W | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:48 x Speed ATAPI (IDE) CD-ROM Decoder with On-Chip Digital Servo System |
發布緊急采購，3分鐘左右您將得到回復。