- 您現在的位置：買賣IC網 > PDF目錄358767 > LC80101M (Sanyo Electric Co.,Ltd.) Special-Purpose Descrambler LSI for Use In VICS Systems.(用于VICS系統的特殊用途密碼器LSI) PDF資料下載
參數資料
| 型號： | LC80101M |
| 廠商： | Sanyo Electric Co.,Ltd. |
| 英文描述： | Special-Purpose Descrambler LSI for Use In VICS Systems.(用于VICS系統的特殊用途密碼器LSI) |
| 中文描述： | 特殊的利用目的解擾器大規模集成電路在VICS系統。（用于VICS系統的特殊用途密碼器大規模集成電路） |
| 文件頁數： | 8/9頁 |
| 文件大?。?/td> | 162K |
| 代理商： | LC80101M |
Usage Notes
1. Setting the BACKUP pin low switches the LC80101M to backup mode. This is a mode in which oscillator and chip
operation are stopped to reduce current drain. This pin must be set high for normal operation. Also note that a reset
must be applied after the BACKUP pin is returned to high from low. (See Figure 4 on page 8.) The BACKUP pin
must be connected to the LC80101M V
DD
pin if backup mode is not used.
2. The lines connecting this LSI to the LC72700E must be dedicated lines only used by these two chips. Do not connect
these lines to any other circuits via a bus or any other connection.
3. A reset must be applied when power is first applied. The LC72700E RST pin and this LSI’s RST2 pin can be driven
from a common signal. (See Figure 3 on page 8.)
4. The TESTON pin (pin 13) must be connected to ground.
Operation During Reset
A reset signal is applied by setting the RST2 pin input level below V
IL
for at least 300 ns when the power-supply voltage
(V
DD
) is 3.4 V or higher. See Figure 3.
Figure 3
All registers other than those holding data required for descrambling are reset by a reset signal. The crystal oscillator
circuit does not stop.
BACKUP Pin
A reset must be applied after the BACKUP pin is returned to high (for normal operation from low (backup mode, in
which the oscillator is stopped). See the following figure.
Figure 4
No. 5438-8/9
LC80101M
相關PDF資料 |
PDF描述 |
|---|---|
| LC810 | LC 810 High Density Power Converter |
| LC81096 | |
| LC82101 | Image Processing Circuit for FAX, Copier, and OCR Products |
| LC82102 | Image-Processing LSI for Fax, Copier and OCR Products |
| LC82102W | Image-Processing LSI for Fax, Copier and OCR Products |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LC8011-21 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Optoelectronic |
| LC8021-21 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Optoelectronic |
| LC8031-21 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Optoelectronic |
| LC8041-21 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Optoelectronic |
| LC8041R11 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Optoelectronic |
發布緊急采購，3分鐘左右您將得到回復。