參數資料
型號： KSZ8851-16MLL-EVAL
廠商： Micrel Inc
文件頁數： 21/84頁
文件大小： 0K
描述： BOARD EVALUATION KSZ8851-16MLL
產品培訓模塊： KSZ8851 10/100 Embedded Controllers
標準包裝： 1
系列： LinkMD®
主要目的： 接口，以太網控制器（PHY 和 MAC）
嵌入式： 否
已用 IC / 零件： KSZ8851-16MLL
主要屬性： 1 個端口，100BASE-TX/10BASE-T
次要屬性： 8/16 位接口，LinkMD 線纜診斷
已供物品： 板，文檔
產品目錄頁面： 1081 (CN2011-ZH PDF)
相關產品： 576-3438-ND - IC CTLR MAC/PHY NON PCI 128PQFP
576-3253-ND - IC CTLR MAC/PHY NON-PCI 128-PQFP
576-3252-ND - IC CTLR MAC/PHY NON-PCI 48-LQFP
其它名稱： 576-3292
Micrel, Inc.
KSZ8851-16MLL/MLLI
March 11, 2014
28
Revision 2.2
Driver Routine for Transmit Packet from Host Processor to KSZ8851-16MLL
The transmit routine is called by the upper layer to transmit a contiguous block of data through the Ethernet controller. It is
user’s choice to decide how the transmit routine is implemented. If the Ethernet controller encounters an error while
transmitting the frame, it’s the user’s choice to decide whether the driver should attempt to retransmit the same frame or
discard the data. The following Figures 7 shows the step-by-step for single transmit packets from host processor to
KSZ8851-16MLL.
Figure 7. Host TX Single Frame in Manual Enqueue Flow Diagram
Host receives an Ethernet pkt from
upper layer and prepares transmit pkt
data (data, data_length, frame ID).
The transmit queue frame format is
shown in Table 5
Check if KSZ8851M TXQ
Memory size is available for this
transmit pkt?
(Read TXMIR Reg)
Write an “1” to RXQCR[3] reg to enable
TXQ write access, then Host starts
write transmit data (control word, byte
count and pkt data) to TXQ memory.
This is moving transmit data from Host
to KSZ8851M TXQ memory until whole
pkt is finished
Write an “0” to RXQCR[3] reg to end
TXQ write access
Write an “1” to TXQCR[0] reg to issue a
transmit command (manual-enqueue)
to the TXQ. The TXQ will transmit this
pkt data to the PHY port
Option to Read ISR[14] reg, it indicates
that the TXQ has completed to transmit
at least one pkt to the PHY port, then
Write “1” to clear this bit
Yes
No
Write the total amount of TXQ buffer
space which is required for next
transmit frame size in double-word
count in TXNTFSR[15:0] register
Set bit 1=1 in TXQCR register to
enable the TXQ memory available
monitor
Wait for interrupt
and check if the bit 6=1
(memory space available)
in ISR register
?
Yes
No
相關PDF資料
PDF描述
MLF2012DR15M INDUCTOR MULTILAYER .15UH 0805
0210491067 CABLE JUMPER 1.25MM .203M 35POS
MLF2012A4R7M INDUCTOR MULTILAYER 4.7UH 0805
RNF-100-3/16-BK-STK HEATSHRINK RNF-100 3/16"X4' BLK
EVAL-ADF4158EB1Z BOARD EVALUATION FOR ADF4158
相關代理商/技術參數
參數描述
KSZ8851-16MLL-EVAL 制造商:Micrel Inc 功能描述:BOARD EVALUATION FOR KSZ8851-16MLL
KSZ8851-16MLLI 功能描述:以太網 IC 10/100BT Ethernet MAC + PHY with Generic (8, 16-bit) Bus Interface (I-Temp, Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8851-16MLLI TR 功能描述:以太網 IC 10/100BT Ethernet MAC + PHY with Generic (8, 16-bit) Bus Interface (I-Temp, Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8851-16MLLJ 功能描述:以太網 IC Single-Port Ethernet MAC Controller with 8/16-Bit Non-PCI Interface (125C support) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8851-16MLLJ_10 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:Single-Port Ethernet MAC Controller with 8-Bit or 16-Bit Non-PCI Interface
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*