參數資料
型號： ISP1181B
廠商： NXP Semiconductors N.V.
英文描述： Full-speed Universal Serial Bus peripheral controller
中文描述： 全速通用串行總線外設控制器
文件頁數： 25/70頁
文件大?。?/td> 341K
代理商： ISP1181B
Philips Semiconductors
ISP1181B
Full-speed USB peripheral controller
Product data
Rev. 02 — 07 December 2004
25 of 70
9397 750 13958
Koninklijke Philips Electronics N.V. 2004. All rights reserved.
[1]
[2]
[3]
[4]
[5]
[6]
[7]
With N representing the number of bytes, the number of words for 16-bit bus width is: (N + 1) DIV 2.
When accessing an 8-bit register in 16-bit mode, the upper byte is invalid.
In 8-bit bus mode this command requires more time to complete than other commands. See
Table 58
.
During isochronous transfer in 16-bit mode, because N
≤
1023, the firmware must take care of the upper byte.
Validating an OUT endpoint buffer causes unpredictable behavior of ISP1181B.
Clearing an IN endpoint buffer causes unpredictable behavior of ISP1181B.
Reads a copy of the Status Register: executing this command does not clear any status bits or interrupt bits.
12.1 Initialization commands
Initialization commands are used during the enumeration process of the USB
network. These commands are used to configure and enable the embedded
endpoints. They also serve to set the USB assigned address of ISP1181B and to
perform a device reset.
12.1.1
Write/Read Endpoint Configuration
This command is used to access the Endpoint Configuration Register (ECR) of the
target endpoint. It defines the endpoint type (isochronous or bulk/interrupt), direction
(OUT/IN), FIFO size and buffering scheme. It also enables the endpoint FIFO. The
register bit allocation is shown in
Table 14
. A bus reset will disable all endpoints.
The allocation of FIFO memory only takes place after
all
16 endpoints have been
configured in sequence (from endpoint 0 OUT to endpoint 14). Although the control
endpoints have fixed configurations, they must be included in the initialization
sequence and be configured with their default values (see
Table 4
). Automatic FIFO
allocation starts when endpoint 14 has been configured.
Unstall Endpoint n
(n = 1 to 14)
Check Control OUT Status
[7]
Endpoint 1 to 14
82 to 8F
-
Endpoint Status Image Register
endpoint 0 OUT
Endpoint Status Image Register
endpoint 0 IN
Endpoint Status Image Register n
endpoint 1 to 14
Endpoint 0 IN and OUT
D0
read 1 byte
[2]
Check Control IN Status
[7]
D1
read 1 byte
[2]
Check Endpoint n Status
(n = 1 to 14)
[7]
Acknowledge Setup
General commands
Read Control OUT Error Code
D2 to DF
read 1 byte
[2]
F4
-
[3]
Error Code Register
endpoint 0 OUT
Error Code Register endpoint 0 IN
Error Code Register
endpoint 1 to 14
all registers with write access
Scratch Register
Frame Number Register
Chip ID Register
Interrupt Register
A0
read 1 byte
[2]
Read Control IN Error Code
Read Endpoint n Error Code
(n = 1 to 14)
Unlock Device
Write/Read Scratch Register
Read Frame Number
Read Chip ID
Read Interrupt Register
A1
A2 to AF
read 1 byte
[2]
read 1 byte
[2]
B0
B2/B3
B4
B5
C0
write 2 bytes
write/read 2 bytes
read 1 or 2 bytes
read 2 bytes
read 4 bytes
Table 13:
Name
Command and register summary
…continued
Destination
Code (Hex)
Transaction
[1]
相關PDF資料
PDF描述
ISP1181BBS Full-speed Universal Serial Bus peripheral controller
ISP1181BDGG Full-speed Universal Serial Bus peripheral controller
ISP1181 Full-speed Universal Serial Bus Interface Device(全速通用串行總線接口器件)
ISP1181DGG INDUCTOR 4.7NH +-.3NH 0402 SMD
ISP1183 Low-power Universal Serial Bus interface device with DMA
相關代理商/技術參數
參數描述
ISP1181BBS 制造商:NXP Semiconductors 功能描述:IC CONTROLLER USB PERIPHERAL SMD 制造商:ST-Ericsson 功能描述:CONTROLLER USB PERIPHERAL 48HVQFN
ISP1181BBS,518 功能描述:USB 接口集成電路 USB 1.1 DEVICE RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
ISP1181BBS,551 功能描述:USB 接口集成電路 USB 1.1 DEVICE CONTROLLER RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
ISP1181BBS,557 功能描述:USB 接口集成電路 DO NOT USE ORDER -S OR -T PART RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
ISP1181BBS518 制造商:ST-Ericsson 功能描述:CONTROLLER USB PERIPHERAL 48HVQFN
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*