- 您現在的位置：買賣IC網 > PDF目錄384532 > ISL95711 (Intersil Corporation) Terminal Voltage 3V or 5V, 128 Taps I2C Serial Interface PDF資料下載
參數資料
| 型號： | ISL95711 |
| 廠商： | Intersil Corporation |
| 英文描述： | Terminal Voltage 3V or 5V, 128 Taps I2C Serial Interface |
| 中文描述： | 終端電壓3V或5V，128絲錐I2C串行接口 |
| 文件頁數： | 9/12頁 |
| 文件大?。?/td> | 333K |
| 代理商： | ISL95711 |
9
FN8241.2
August 15, 2005
Write Operation
A Write operation requires a START condition, followed by a
valid Identification Byte, a valid Address Byte, a Data Byte,
and a STOP condition. After each of the three bytes, the
ISL95711 responds with an ACK. At this time, if the Data
Byte is to be written only to volatile registers, then the device
enters its standby state. If the Data Byte is to be written also
to non-volatile memory, the ISL95711 begins its internal write
cycle to non-volatile memory. During the internal non-volatile
write cycle, the device ignores transitions at the SDA and
SCL pins, and the SDA output is at a high impedance state.
When the internal non-volatile write cycle is completed, the
ISL95711 enters its standby state (See Figure 3).
The byte at address 02h determines if the Data Byte is to be
written to volatile or both volatile and non-volatile. (See
“Memory Description” on page 8.)
Data Protection
A STOP condition acts as a protection of non-volatile
memory. A valid Identification Byte, Address Byte, and total
number of SCL pulses act as a protection of both volatile
and non-volatile registers. During a Write sequence, the
Data Byte is loaded into an internal shift register as it is
received. If the Address Byte is 0 or 2, the Data Byte is
transferred to the Wiper Register (WR) or to the Access
Control Register respectively, at the falling edge of the SCL
pulse that loads the last bit (LSB) of the Data Byte. If the
Address Byte is 0, and the Access Control Register is all
zeros (default), then the STOP condition initiates the internal
write cycle to non-volatile memory.
Read Operation
A Read operation consists of a three byte instruction
followed by one or more Data Bytes (See Figure 4). The
master initiates the operation issuing the following
sequence: a START, the Identification byte with the R/W bit
set to “0”, an Address Byte, a second START, and a second
Identification byte with the R/W bit set to “1”. After each of
the three bytes, the ISL95711 responds with an ACK; then
the ISL95711 transmits the Data Byte. The master then
terminates the read operation (issuing a STOP condition)
following the last bit of the Data Byte (See Figure 4).
The byte at address 02h determines if the Data Bytes being
read are from volatile or non-volatile memory. (See “Memory
Description”.)
FIGURE 1. VALID DATA CHANGES, START, AND STOP CONDITIONS
FIGURE 2. ACKNOWLEDGE RESPONSE FROM RECEIVER
SDA
SCL
START
DATA
STABLE
DATA
CHANGE
STOP
DATA
STABLE
SDA OUTPUT FROM
TRANSMITTER
SDA OUTPUT FROM
RECEIVER
8
1
9
START
ACK
SCL FROM
MASTER
HIGH IMPEDANCE
HIGH IMPEDANCE
ISL95711
相關PDF資料 |
PDF描述 |
|---|---|
| ISL95711UIU10Z-T | Hook-Up Wire; Conductor Size AWG:18; No. Strands x Strand Size:19 x 30; Jacket Color:Light Blue; Approval Bodies:UL; Approval Categories:UL AWM Style 1180; Passes VW-1 Flame Test; Cable/Wire MIL SPEC:MIL-W-16878/5 Type EE RoHS Compliant: Yes |
| ISL95711UIU10Z | Terminal Voltage 3V or 5V, 128 Taps I2C Serial Interface |
| ISL95711WIU10Z | Terminal Voltage 3V or 5V, 128 Taps I2C Serial Interface |
| ISL95711WIU10Z-T | Terminal Voltage 3V or 5V, 128 Taps I2C Serial Interface |
| ISL96017_06 | 128-Tap DCP, 16kbit EEPROM, and I2C Serial Interface |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL95711UIU10Z | 功能描述:IC POT DGTL 50K OHM 10-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 標準包裝:3,300 系列:WiperLock™ 接片:257 電阻（歐姆）:100k 電路數:1 溫度系數:標準值 150 ppm/°C 存儲器類型:易失 接口:3 線 SPI（芯片選擇） 電源電壓:1.8 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-VDFN 裸露焊盤 供應商設備封裝:8-DFN-EP（3x3） 包裝:帶卷 (TR) |
| ISL95711UIU10Z-T | 功能描述:IC POT DGTL 50K OHM 10-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 標準包裝:3,000 系列:DPP 接片:32 電阻（歐姆）:10k 電路數:1 溫度系數:標準值 300 ppm/°C 存儲器類型:非易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.5 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WFDFN 裸露焊盤 供應商設備封裝:8-TDFN（2x3） 包裝:帶卷 (TR) |
| ISL95711WIU10Z | 功能描述:IC XDCP 128-TAP 10KOHM 10-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 標準包裝:3,000 系列:DPP 接片:32 電阻（歐姆）:10k 電路數:1 溫度系數:標準值 300 ppm/°C 存儲器類型:非易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.5 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WFDFN 裸露焊盤 供應商設備封裝:8-TDFN（2x3） 包裝:帶卷 (TR) |
| ISL95711WIU10Z-T | 功能描述:IC POT DGTL 10K OHM 10-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 標準包裝:3,000 系列:DPP 接片:32 電阻（歐姆）:10k 電路數:1 溫度系數:標準值 300 ppm/°C 存儲器類型:非易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.5 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WFDFN 裸露焊盤 供應商設備封裝:8-TDFN（2x3） 包裝:帶卷 (TR) |
| ISL95810UI8Z | 制造商:Intersil Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。