- 您現在的位置：買賣IC網 > PDF目錄384527 > ISL6740A (Intersil Corporation) Flexible Double-Ended Voltage-Mode PWM Controller with Voltage Feed Forward PDF資料下載
參數資料
| 型號： | ISL6740A |
| 廠商： | Intersil Corporation |
| 英文描述： | Flexible Double-Ended Voltage-Mode PWM Controller with Voltage Feed Forward |
| 中文描述： | 靈活的雙端電壓模式PWM控制器與電壓前饋 |
| 文件頁數： | 11/15頁 |
| 文件大?。?/td> | 320K |
| 代理商： | ISL6740A |
11
FN9195.0
February 7, 2005
UV/Inhibit fault; otherwise, it is inactive and does not affect
the node voltage. The magnitude of the hysteresis is a
function of the external resistor divider impedance. If the
resistor divider impedance results in too little hysteresis, a
series resistor between the UV pin and the divider may be
used to increase the hysteresis. A soft-start cycle begins
when the UV/Inhibit fault clears.
The voltage hysteresis created by the switched current
source and the external impedance is generally small due to
the large resistor divider ratio required to scale the input
voltage down to the UV threshold level. A small capacitor
placed between the UV input and ground may be required to
filter noise out.
As V
IN
decreases to a UV condition, the threshold level is:
The hysteresis voltage,
V, is:
Setting R3 equal to zero results in the minimum hysteresis,
and yields:
As V
IN
increases from a UV condition, the threshold level is:
Output voltage variation caused by changes in the supply
voltage may be virtually removed through a technique known
as feed forward compensation. Using feed forward, the duty
cycle is directly modulated based on changes in the input
voltage only. No closed loop feedback system is required.
The feed forward circuit uses the voltage applied to the
UV/FF pin to modulate the oscillator ramp amplitude with
minimal effect on the switching frequency and deadtime of
the oscillator. The voltage feed forward operates over a 3:1
input voltage range.
The voltage applied to the UV/FF pin is multiplied by 0.8 and
output on the R
TC
and R
TD
pins. This voltage is also
summed with the C
T
valley threshold voltage (0.8 V) to
create the C
T
peak threshold voltage. As the voltage applied
to UV/FF varies, the CT peak voltage and the CT charge and
discharge currents vary, all in direct proportion to each other.
The result is an amplitude modulated sawtooth waveform on
C
T
that is frequency invariant.
The voltage amplitude of C
T
ranges from 1.6V to 4.2V as the
voltage on UV increases. The UV threshold defines the
minimum amplitude of C
T
and corresponds to maximum duty
cycle operation.
For unregulated bus converters and DC transformers, feed
forward can compensate for input voltage variations without
a closed loop feedback network. A resistive voltage divider
from V
REF
to V
ERROR
sets the feed forward control voltage.
For example, if the desired duty cycle at the minimum
operating voltage is 90%, then
Overcurrent Protection
There are two overcurrent protection mechanisms in the
ISL6740A, one for light overcurrent and one for heavy over
load. They are referred to, respectively, as overcurrent
protection and short circuit protection.
Overcurrent Operation
Overcurrent delayed shutdown is enabled once the soft-start
cycle is complete. If an overcurrent condition is detected, the
soft-start charging current source is disabled and the soft-
start capacitor is allowed to discharge through a 15
μ
A
source. At the same time a 50
μ
s re-triggerable one-shot
timer is activated. It remains active for 50
μ
s after the
overcurrent condition ceases. If the soft-start capacitor
discharges by more then 0.25V to 4.25V, the output is
disabled and the Fault signal asserted. This state continues
until the soft-start voltage reaches 270mV, at which time a
new soft-start cycle is initiated. If the overcurrent condition
FIGURE 5. UV HYSTERESIS
V
IN
R1
R2
R3
1.00V
10
μ
A
ON
+
-
V
IN DOWN
)
--------+
R2
=
V
(EQ. 7)
V
10
5
–
R1
R3
--------+
+
=
V
(EQ. 8)
V
10
5
–
R1
=
V
(EQ. 9)
V
IN UP
)
V
IN DOWN
)
V
+
=
V
(EQ. 10)
FIGURE 6. FEED FORWARD BEHAVIOR
V
UV/FF
V
ERROR
CT
OUTA
OUTB
V
ERROR
D
max
V
UV FF
0.8
(
)
0.8
+
=
V
0.9 1.0
0.8
)
0.8
+
1.52
=
=
V
(EQ. 11)
ISL6740A
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6740AIVZA | JT 5C 5#20 PIN PLUG |
| ISL6740AIVZA-T | Flexible Double-Ended Voltage-Mode PWM Controller with Voltage Feed Forward |
| ISL6742 | Octal Buffers/Drivers With 3-State Outputs 20-SSOP -40 to 85 |
| ISL6742AAZA-T | Advanced Double-Ended PWM Controller |
| ISL6742AAZA | Octal Buffers/Drivers With 3-State Outputs 20-SSOP -40 to 85 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6740AIVZA | 功能描述:IC REG CTRLR PWM VM 16-TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) |
| ISL6740AIVZA-T | 功能描述:IC REG CTRLR PWM VM 16-TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) |
| ISL6740EVAL1 | 功能描述:EVALUATION BOARD 1 ISL6740 RoHS:否 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:True Shutdown™ 主要目的:DC/DC，步升 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:- 電流 - 輸出:1A 輸入電壓:2.5 V ~ 5.5 V 穩壓器拓?fù)浣Y(jié)構:升壓 頻率 - 開關:3MHz 板類型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| ISL6740EVAL2 | 功能描述:EVALUATION BOARD 2 ISL6740 RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 傳感器類型:CMOS 成像，彩色（RGB） 傳感范圍:WVGA 接口:I²C 靈敏度:60 fps 電源電壓:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相關產品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP |
| ISL6740EVAL2Z | 功能描述:EVALUATION BOARD 2 ISL6740 RoHS:是 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:True Shutdown™ 主要目的:DC/DC，步升 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:- 電流 - 輸出:1A 輸入電壓:2.5 V ~ 5.5 V 穩壓器拓?fù)浣Y(jié)構:升壓 頻率 - 開關:3MHz 板類型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
發布緊急采購，3分鐘左右您將得到回復。