- 您現在的位置：買賣IC網 > PDF目錄384526 > ISL6595 (Intersil Corporation) Digital Multiphase Controller PDF資料下載
參數資料
| 型號： | ISL6595 |
| 廠商： | Intersil Corporation |
| 英文描述： | Digital Multiphase Controller |
| 中文描述： | 數字多相控制器 |
| 文件頁數： | 17/21頁 |
| 文件大小： | 566K |
| 代理商： | ISL6595 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁
17
FN9192.0
February 27, 2006
will respond. If the transient is severe, up to three phases
respond. This avoids a dramatic sinking or sourcing event,
which can cause oscillation. The ISL6595 controller itself
uses hysteretic control algorithms after the transient event to
ensure that the power stages return to normal operation
smoothly with minimal ringing. External-loop ATR
(overshoot only) provides an output to engage an additional
low latency low side stage capable of quickly discharging the
load. This consists of a small low-side FET with a very fast
gate driver. Internal- and external-loop ATR can be used
independently or in conjunction to optimize transient
performance.
Output Configurations
The ISL6595 provides 6 configurable outputs that are used
to drive up to 6 phase power stages. The PWM6 output may
also be configured to provide the external loop ATRL output
to drive a low side overshoot control FET.
For driving external MOSFETs, tri-valent FET drivers must
be used. The driver input circuit has two thresholds (upper
and lower) along with a bias network such that its input is
centered between the two thresholds when the ISL6595
output driver is three-stated. This allows three values to be
defined for the signal, depending whether the output is high,
low, or high impedance. If the input signal is high, the gate
driver turns the high-side switch on. If the input signal is low,
the gate driver turns the low-side switch on. If the input
signal is three-state, the driver does not turn either high-side
or low-side switches on and the power stage is high
impedance or three-stated. Intersil’s ISL6594A/B and
ISL6596 FET drivers are optimized to operate with the
ISL6595.
The output drive signals are generated using a 3.3V tri-
valent driver. All outputs are tri-stated during reset,
configuration, and inactive state. This allows the user to set
the appropriate level to tri-state the power stage, using
external pull-up or pull-down resistors.
Output Firing Sequence
The PWM output and current sense (ISEN) pins of the
ISL6595 have been assigned such that they can be placed
sequentially for PC board layouts (i.e. phase 2 next to 1,
phase 3 next to 2, etc...). The output phases are set in a
pre-wired firing order to facilitate layout of high phase count
systems. For high phase count systems, the VRD layout in
the motherboard will likely require the power components to
be laid out across two sides of the processor. The firing
sequence shown in the table below ensures that for a highly
distributed power array, the maximum spatial distribution can
be obtained between sequential phases.
Fault Detection and Fault Handling
The ISL6595 provides a very flexible fault detection reporting
and handling mechanism. Fault detection capability
includes:
Input Undervoltage Protection (IUVP)
Output Overvoltage Protection (OOVP)
Output Undervoltage Protection (OUVP)
Per Phase Overcurrent Protection (OCP)
Total Output Overcurrent
Two levels of Internal Temperature Protection
Four levels of External Temperature Protection
Configuration Failure
Calibration Time-out Failure
All individual faults are latched and reported over the serial
interface. Two configurable fault outputs are provided
(FAULT1, FAULT2). Each output allows independent
masking of all faults, allowing a subset of faults to be
reported over that pin. The outputs can also be configured
as either latched or unlatched, active high or active low
polarity, and CMOS or open drain outputs.
Typical usage of the configurable fault pins would be as a
crowbar signal to drive an external crowbar device,
temperature alert to notify the system a thermal shutdown is
imminent, or as an interrupt to cause a micro-controller to
poll the fault registers.
Shutdown operation also allows a subset of faults to be
individually masked. Additionally, the shutdown recovery
can be either autonomous or latched. For autonomous
recovery, the faults are not latched, so if the fault condition is
eliminated when the controller returns to an inactive state, it
will wait for a programmable time period, and then attempt a
new soft start. If the fault condition reoccurs, the controller
will recommence the shutdown sequence, continuing this
cycle indefinitely until the fault conditions is eliminated. The
programmable delay ensures a sufficiently low duty cycle to
prevent the regulator components from being damaged from
power cycling, assuming the fault condition itself is not
immediately destructive.
TABLE 3. OUTPUT FIRING SEQUENCE AND NUMBER OF
PHASES
#P
FIRING SEQUENCE
2
1
2
1
2
1
2
1
2
1
2
1
2 …
3
1
2
3
1
2
3
1
2
3
1
2
3 …
4
1
4
2
3
1
4
2
3
1
4
2
3 …
5
1
4
2
5
3
1
4
2
5
3
1
4 …
6
1
4
2
5
3
6
1
4
2
5
3
6 …
ISL6595
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6597CRZ | Dual Synchronous Rectified MOSFET Drivers |
| ISL6597 | Dual Low-Noise Wide-Bandwidth Precision Amplifier 8-TSSOP -40 to 85 |
| ISL6608CB-T | Synchronous Rectified MOSFET Driver |
| ISL6608IBZ | Synchronous Rectified MOSFET Driver |
| ISL6608IBZ-T | Synchronous Rectified MOSFET Driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6595DRZ | 功能描述:IC DIGITL MULTIPHASE CTRLR 48QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電源控制器，監視器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（5x5） 包裝:帶卷 (TR) |
| ISL6595DRZ-T | 功能描述:IC DIGITL MULTIPHASE CTRLR 48QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電源控制器，監視器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（5x5） 包裝:帶卷 (TR) |
| ISL6595DRZ-TK | 功能描述:IC DIGITL MULTIPHASE CTRLR 48QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電源控制器，監視器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（5x5） 包裝:帶卷 (TR) |
| ISL6595EVAL2 | 制造商:Intersil Corporation 功能描述:DGTL MULTIPHASE CNTRLR - Bulk |
| ISL6596CBZ | 功能描述:IC MOSFET DRVR SYNC BUCK 8-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - MOSFET，電橋驅動器 - 外部開關 系列:- 標準包裝:50 系列:- 配置:高端 輸入類型:非反相 延遲時間:200ns 電流 - 峰:250mA 配置數:1 輸出數:1 高端電壓 - 最大（自引導啟動）:600V 電源電壓:12 V ~ 20 V 工作溫度:-40°C ~ 125°C 安裝類型:通孔 封裝/外殼:8-DIP（0.300"，7.62mm） 供應商設備封裝:8-DIP 包裝:管件 其它名稱:*IR2127 |
發布緊急采購，3分鐘左右您將得到回復。