- 您現在的位置：買賣IC網 > PDF目錄383159 > ISL6568CRZA (INTERSIL CORP) Two-Phase Buck PWM Controller with Integrated MOSFET Drivers for VRM9, VRM10, and AMD Hammer Applications PDF資料下載
參數資料
| 型號： | ISL6568CRZA |
| 廠商： | INTERSIL CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Two-Phase Buck PWM Controller with Integrated MOSFET Drivers for VRM9, VRM10, and AMD Hammer Applications |
| 中文描述： | SWITCHING CONTROLLER, 1500 kHz SWITCHING FREQ-MAX, PQCC32 |
| 封裝： | 5 X 5 MM, ROHS COMPLIANT, PLASTIC, MO-220-VHHD, MLFP, QFN-32 |
| 文件頁數： | 10/28頁 |
| 文件大?。?/td> | 716K |
| 代理商： | ISL6568CRZA |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
10
FN9187.3
July 25, 2005
pulse termination signal is the inverse of the switching
frequency set by the resistor between the FS pin and
ground. Each cycle begins when the clock signal commands
PWM1 to go low. The PWM1 transition signals the internal
channel-1 MOSFET driver to turn off the channel-1 upper
MOSFET and turn on the channel-1 synchronous MOSFET.
In the default channel configuration, the PWM2 pulse
terminates 1/2 of a cycle after the PWM1 pulse.
If the BOOT2 and PHASE2 pins are both connected to +12V
single channel operation is selected.
Once a PWM pulse transitions low, it is held low for a
minimum of 1/3 cycle. This forced off time is required to
ensure an accurate current sample. Current sensing is
described in the next section. After the forced off time
expires, the PWM output is enabled. The PWM output state
is driven by the position of the error amplifier output signal,
V
COMP
, minus the current correction signal relative to the
sawtooth ramp as illustrated in Figure 3. When the modified
V
COMP
voltage crosses the sawtooth ramp, the PWM output
transitions high. The internal MOSFET driver detects the
change in state of the PWM signal and turns off the
synchronous MOSFET and turns on the upper MOSFET.
The PWM signal will remain high until the pulse termination
signal marks the beginning of the next cycle by triggering the
PWM signal low.
Channel-Current Balance
One important benefit of multi-phase operation is the thermal
advantage gained by distributing the dissipated heat over
multiple devices and greater area. By doing this the designer
avoids the complexity of driving parallel MOSFETs and the
expense of using expensive heat sinks and exotic magnetic
materials.
In order to realize the thermal advantage, it is important that
each channel in a multi-phase converter be controlled to
carry about the same amount of current at any load level. To
achieve this, the currents through each channel must be
sampled every switching cycle. The sampled currents, I
n
,
from each active channel are summed together and divided
by the number of active channels. The resulting cycle
average current, I
AVG
, provides a measure of the total load-
current demand on the converter during each switching
cycle. Channel-current balance is achieved by comparing
the sampled current of each channel to the cycle average
current, and making the proper adjustment to each channel
pulse width based on the error. Intersil’s patented current-
balance method is illustrated in Figure 3, with error
correction for channel 1 represented. In the figure, the cycle
average current, I
AVG
, is compared with the channel 1
sample, I
1
, to create an error signal I
ER
.
The filtered error signal modifies the pulse width
commanded by V
COMP
to correct any unbalance and force
I
ER
toward zero. The same method for error signal
correction is applied to each active channel.
Current Sampling
In order to realize proper current-balance, the currents in
each channel must be sampled every switching cycle. This
sampling occurs during the forced off-time, following a PWM
transition low. During this time the current-sense amplifier
uses the ISEN inputs to reproduce a signal proportional to
the inductor current, I
L
. This sensed current, I
SEN
, is simply
a scaled version of the inductor current. The sample window
opens exactly 1/6 of the switching period, t
SW
, after the
PWM transitions low. The sample window then stays open
the rest of the switching cycle until PWM transitions high
again, as illustrated in Figure 4.
The sampled current, at the end of the t
SAMPLE
, is
proportional to the inductor current and is held until the next
switching period sample. The sampled current is used only
for channel-current balance.
The ISL6568 supports MOSFET r
DS(ON)
current sensing to
sample each channel’s current for channel-current balance.
The internal circuitry, shown in Figure 5 represents channel
n of an N-channel converter. This circuitry is repeated for
each channel in the converter, but may not be active
FIGURE 3. CHANNEL-1 PWM FUNCTION AND CURRENT-
BALANCE ADJUSTMENT
÷
N
I
AVG
I
2
Σ
-
+
+
-
+
-
f(s)
PWM1
I
1
V
COMP
SAWTOOTH SIGNAL
I
ER
NOTE: Channel 2 is optional.
FILTER
TO GATE
CONTROL
LOGIC
FIGURE 4. SAMPLE AND HOLD TIMING
TIME
PWM
I
L
I
SEN
SWITCHING PERIOD
SAMPLING PERIOD
OLD SAMPLE
CURRENT
NEW SAMPLE
CURRENT
ISL6568
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6568 | Dual Low-Noise Wide-Bandwidth Precision Amplifier 8-SOIC -40 to 85 |
| ISL6568IR | CONNECTOR ACCESSORY |
| ISL6568IR-T | Two-Phase Buck PWM Controller with Integrated MOSFET Drivers for VRM9, VRM10, and AMD Hammer Applications |
| ISL6568IRZ | Two-Phase Buck PWM Controller with Integrated MOSFET Drivers for VRM9, VRM10, and AMD Hammer Applications |
| ISL6568IRZ-T | Two-Phase Buck PWM Controller with Integrated MOSFET Drivers for VRM9, VRM10, and AMD Hammer Applications |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6568CRZA-T | 制造商:Intersil Corporation 功能描述:CURRENT MODE PWM CNTRLR 0.8375V TO 12V 60A 32QFN EP - Tape and Reel 制造商:Intersil 功能描述:W/ANNEAL 2-PHS PWM CNTRLR W/2-DRVRS |
| ISL6568CRZR5184 | 功能描述:IC CTRLR PWM 2PHASE BUCK 32-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:43 系列:- 應用:控制器，Intel VR11 輸入電壓:5 V ~ 12 V 輸出數:1 輸出電壓:0.5 V ~ 1.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-QFN（7x7） 包裝:管件 |
| ISL6568CRZ-T | 功能描述:IC CTLR PWM BUCK 2PHASE 32-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,000 系列:- 應用:電源，ICERA E400，E450 輸入電壓:4.1 V ~ 5.5 V 輸出數:10 輸出電壓:可編程 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:42-WFBGA，WLCSP 供應商設備封裝:42-WLP 包裝:帶卷 (TR) |
| ISL6568CRZ-TKR5184 | 功能描述:IC CTRLR PWM 2PHASE BUCK 32-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:43 系列:- 應用:控制器，Intel VR11 輸入電壓:5 V ~ 12 V 輸出數:1 輸出電壓:0.5 V ~ 1.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-QFN（7x7） 包裝:管件 |
| ISL6568CRZ-TR5184 | 功能描述:IC CTRLR PWM 2PHASE BUCK 32-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:2,000 系列:- 應用:控制器，DSP 輸入電壓:4.5 V ~ 25 V 輸出數:2 輸出電壓:最低可調至 1.2V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:30-TFSOP（0.173"，4.40mm 寬） 供應商設備封裝:30-TSSOP 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。