- 您現在的位置：買賣IC網 > PDF目錄384525 > ISL6526AIBZ (INTERSIL CORP) Single Synchronous Buck Pulse-Width Modulation (PWM) Controller PDF資料下載
參數資料
| 型號： | ISL6526AIBZ |
| 廠商： | INTERSIL CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Single Synchronous Buck Pulse-Width Modulation (PWM) Controller |
| 中文描述： | 2 A SWITCHING CONTROLLER, 640 kHz SWITCHING FREQ-MAX, PDSO14 |
| 封裝： | ROHS COMPLIANT, PLASTIC, MS-012-AB, SOIC-14 |
| 文件頁數： | 7/15頁 |
| 文件大?。?/td> | 340K |
| 代理商： | ISL6526AIBZ |
7
FN9055.8
March 20, 2007
ENABLE
This pin is the open-collector enable pin. Pulling this pin to a
level below 0.8V will disable the controller. Disabling the
ISL6526, ISL6526A cause the oscillator to stop, the LGATE
and UGATE outputs to be held low, and the soft-start circuitry
to re-arm.
CT1 and CT2
These pins are the connections for the external charge
pump capacitor. A minimum of a 0.1
μ
F ceramic capacitor is
recommended for proper operation of the IC.
CPVOUT
This pin represents the output of the charge pump. The
voltage at this pin is the bias voltage for the IC. Connect a
decoupling capacitor from this pin to ground. The value of
the decoupling capacitor should be at least 10x the value of
the charge pump capacitor. This pin may be tied to the
bootstrap circuit as the source for creating the BOOT
voltage.
CPGND
This pin represents the signal and power ground for the
charge pump. Tie this pin to the ground island/plane through
the lowest impedance connection available.
Functional Description
Initialization
The ISL6526, ISL6526A automatically initialize upon receipt
of power. Special sequencing of the input supplies is not
necessary. The Power-On Reset (POR) function continually
monitors the output voltage of the charge pump. During
POR, the charge pump operates on a free running oscillator.
Once the POR level is reached, the charge pump oscillator
is synched to the PWM oscillator. The POR function also
initiates the soft-start operation after the charge pump output
voltage exceeds its POR threshold.
Soft-Start
The POR function initiates the digital soft-start sequence.
The PWM error amplifier reference is clamped to a level
proportional to the soft-start voltage. As the soft-start voltage
slews up, the PWM comparator generates PHASE pulses of
increasing width that charge the output capacitor(s). This
method provides a rapid and controlled output voltage rise.
The soft-start sequence typically takes about 6.5ms.
Figure 1 shows the soft-start sequence for a typical application.
At t0, the +3.3V VCC voltage starts to ramp. At time t1, the
Charge Pump begins operation and the +5V CPVOUT IC bias
voltage starts to ramp up. Once the voltage on CPVOUT
crosses the POR threshold at time t2, the output begins the
soft-start sequence. The triangle waveform from the PWM
oscillator is compared to the rising error amplifier output
voltage. As the error amplifier voltage increases, the pulse-
width on the UGATE pin increases to reach the steady-state
duty cycle at time t3.
Shoot-Through Protection
A shoot-through condition occurs when both the upper
MOSFET and lower MOSFET are turned on simultaneously,
effectively shorting the input voltage to ground. To protect
the regulator from a shoot-through condition, the ISL6526,
ISL6526A incorporate specialized circuitry which insures
that the complementary MOSFETs are not ON
simultaneously.
The adaptive shoot-through protection utilized by the
ISL6526, ISL6526A look at the lower gate drive pin, LGATE,
and the upper gate drive pin, UGATE, to determine whether
a MOSFET is ON or OFF. If the voltage from UGATE or from
LGATE to GND is less than 0.8V, then the respective
MOSFET is defined as being OFF and the complementary
MOSFET is turned ON. This method of shoot-through
protection allows the regulator to sink or source current.
Since the voltage of the lower MOSFET gate and the upper
MOSFET gate are being measured to determine the state of
the MOSFET, the designer is encouraged to consider the
repercussions of introducing external components between
the gate drivers and their respective MOSFET gates before
actually implementing such measures. Doing so may
interfere with the shoot-through protection.
Output Voltage Selection
The output voltage can be programmed to any level between
V
IN
and the internal reference, 0.8V. An external resistor
divider is used to scale the output voltage relative to the
reference voltage and feed it back to the inverting input of
the error amplifier, see Figure 2. However, since the value of
R1 affects the values of the rest of the compensation
components, it is advisable to keep its value less than 5k
Ω
.
R4 can be calculated based on the following equation:
FIGURE 1. SOFT-START INTERVAL
0V
TIME
T2
T3
T0
T1
CPVOUT (5V)
VCC (3.3V)
V
OUT
(2.50V)
(1V/DIV)
R4
–
V
OUT1
-------------------------------------
=
(EQ. 2)
ISL6526, ISL6526A
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6526CRZ | Single Synchronous Buck Pulse-Width Modulation (PWM) Controller |
| ISL6529A | Dual Regulator.Synchronous Rectified Buck PWM and Linear Power Controller |
| ISL6535 | Synchronous Buck Pulse-Width Modulator (PWM) Controller |
| ISL6535CBZ | Synchronous Buck Pulse-Width Modulator (PWM) Controller |
| ISL6535CRZ | Synchronous Buck Pulse-Width Modulator (PWM) Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6526AIR | 功能描述:電壓模式 PWM 控制器 Single Synch Buck RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓撲結構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| ISL6526AIR-T | 功能描述:IC REG CTRLR BUCK PWM VM 16-QFN RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,000 系列:- PWM 型:電壓模式 輸出數:1 頻率 - 最大:1.5MHz 占空比:66.7% 電源電壓:4.75 V ~ 5.25 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 85°C 封裝/外殼:40-VFQFN 裸露焊盤 包裝:帶卷 (TR) |
| ISL6526AIRZ | 功能描述:電壓模式 PWM 控制器 600KHZ SNG PWM W/CHA RGE PUMP 16LD 5X5 RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓撲結構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| ISL6526AIRZ-T | 功能描述:電壓模式 PWM 控制器 600KHZ SINGLE PWM W/CHRG PUMP 16LD 5X5 RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓撲結構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| ISL6526AIRZ-TK | 功能描述:IC REG CTRLR BUCK PWM VM 16-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。