參數資料
型號： ISL6316IRZ
廠商： INTERSIL CORP
元件分類： 穩壓器
英文描述： MINIATURE TOGGLE SWITCH
中文描述： SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PQCC40
封裝： 6 X 6 MM, ROHS COMPLIANT, PLASTIC, MO-220-VJJD-2, QFN-40
文件頁數： 13/29頁
文件大小： 838K
代理商： ISL6316IRZ
13
FN9227.0
August 31, 2005
Once a PWM signal transitions low, it is held low for a
minimum of 1/3 cycle. This forced off time is required to
ensure an accurate current sample. Current sensing is
described in the next section. After the forced off time expires,
the PWM output is enabled. The PWM output state is driven
by the position of the error amplifier output signal, V
COMP
,
minus the current correction signal relative to the sawtooth
ramp as illustrated in Figure 7. When the modified V
COMP
voltage crosses the sawtooth ramp, the PWM output
transitions high. The MOSFET driver detects the change in
state of the PWM signal and turns off the synchronous
MOSFET and turns on the upper MOSFET. The PWM signal
will remain high until the pulse termination signal marks the
beginning of the next cycle by triggering the PWM signal low.
Current Sampling
During the forced off-time following a PWM transition low, the
associated channel current sense amplifier uses the ISEN
inputs to reproduce a signal proportional to the inductor
current, I
L
. This current gets sampled starting 1/6 period after
each PWM goes low and continuously gets sampled for 1/3
period, or until the PWM goes high, whichever comes first. No
matter the current sense method, the sense current, I
SEN
, is
simply a scaled version of the inductor current. Coincident
with the falling edge of the PWM signal, the sample and hold
circuitry samples the sensed current signal I
SEN
, as illustrated
in Figure 3.
Therefore, the sample current, I
n
, is proportional to the output
current and held for one switching cycle. The sample current
is used for current balance, load-line regulation, and
overcurrent protection.
Current Sensing
The ISL6316 supports inductor DCR sensing, MOSFET
R
DS(ON)
sensing, or resistive sensing techniques. The
internal circuitry, shown in Figures 4, 5, and 6, represents one
channel of an N-channel converter. This circuitry is repeated
for each channel in the converter, but may not be active
depending on the status of the PWM3 and PWM4 pins, as
described in the
PWM Operation
section.
INDUCTOR DCR SENSING
An inductor’s winding is characteristic of a distributed
resistance as measured by the DCR (Direct Current
Resistance) parameter. Consider the inductor DCR as a
separate lumped quantity, as shown in Figure 4. The channel
current I
L
, flowing through the inductor, will also pass through
the DCR. Equation 3 shows the s-domain equivalent voltage
across the inductor V
L
.
A simple R-C network across the inductor extracts the DCR
voltage, as shown in Figure 4.
The voltage on the capacitor V
C
, can be shown to be
proportional to the channel current I
L
, see Equation 4.
If the R-C network components are selected such that the RC
time constant (= R*C) matches the inductor time constant
(= L/DCR), the voltage across the capacitor V
C
is equal to the
voltage drop across the DCR, i.e. proportional to the channel
current.
FIGURE 3. SAMPLE AND HOLD TIMING
TIME
PWM
I
L
SWITCHING PERIOD
I
SEN
0.5Tsw
SAMPLE CURRENT, I
n
V
L
I
L
s L
DCR
+
(
)
=
(EQ. 3)
V
C
s
-------------
1
+
--------------------------------------+
DCR I
L
(
)
=
(EQ. 4)
FIGURE 4. DCR SENSING CONFIGURATION
I
n
I
SEN
I
L
R
ISEN
-----------------
=
-
+
ISEN-(n)
SAMPLE
&
HOLD
ISL6316 INTERNAL CIRCUIT
V
IN
ISEN+(n)
PWM(n)
ISL6605
R
ISEN(n)
(PTC)
DCR
L
INDUCTOR
R
V
OUT
C
OUT
-
+V
C
(s)
C
ILs
( )
-
+
V
L
ISL6316
相關PDF資料
PDF描述
ISL6316CRZ Enhanced 4-Phase PWM Controller with 6-Bit VID Code Capable of Precision RDS(ON) or DCR Differential Current Sensing for VR10 Application
ISL6316CRZ-T Quadruple 2-Input Exclusive-OR Gates 14-PDIP -40 to 85
ISL6316IRZ-T Quadruple 2-Input Exclusive-OR Gates 14-PDIP -40 to 85
ISL6401 Synchronizing Current Mode PWM for Subscriber Line Interface Circuits (SLICs)(用戶線接口電路(SLICs)專用同步電流模式PWM)
ISL6401CB-T Synchronizing Current Mode PWM for Subscriber Line Interface Circuits (SLICs)
相關代理商/技術參數
參數描述
ISL6316IRZ-T 功能描述:軟開關 PWM 控制器 W/ANNEAL ISL6306 CNTRLR INDUSTRIAL RoHS:否 制造商:Fairchild Semiconductor 輸出端數量: 輸出電流: 開關頻率: 工作電源電壓:30 V 電源電流: 最大工作溫度:+ 105 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel
ISL6322CRZ 功能描述:IC CTRLR PWM 4PHASE BUCK 48-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,000 系列:- 應用:電源，ICERA E400，E450 輸入電壓:4.1 V ~ 5.5 V 輸出數:10 輸出電壓:可編程 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:42-WFBGA，WLCSP 供應商設備封裝:42-WLP 包裝:帶卷 (TR)
ISL6322CRZ-T 功能描述:IC CTRLR PWM 4PHASE BUCK 48-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,000 系列:- 應用:電源，ICERA E400，E450 輸入電壓:4.1 V ~ 5.5 V 輸出數:10 輸出電壓:可編程 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:42-WFBGA，WLCSP 供應商設備封裝:42-WLP 包裝:帶卷 (TR)
ISL6322GCRZ 功能描述:IC CTRLR PWM BUCK 48-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:2,000 系列:- 應用:控制器，DSP 輸入電壓:4.5 V ~ 25 V 輸出數:2 輸出電壓:最低可調至 1.2V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:30-TFSOP（0.173"，4.40mm 寬） 供應商設備封裝:30-TSSOP 包裝:帶卷 (TR)
ISL6322GCRZ-T 功能描述:IC CTRLR PWM BUCK 48-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:43 系列:- 應用:控制器，Intel VR11 輸入電壓:5 V ~ 12 V 輸出數:1 輸出電壓:0.5 V ~ 1.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-QFN（7x7） 包裝:管件
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*