- 您現在的位置：買賣IC網 > PDF目錄384524 > ISL6293-2CR (INTERSIL CORP) Dual Positive-Edge-Triggered D-Type Flip-Flops With Clear and Preset 14-SOIC -40 to 85 PDF資料下載
參數資料
| 型號： | ISL6293-2CR |
| 廠商： | INTERSIL CORP |
| 元件分類： | 電源管理 |
| 英文描述： | Dual Positive-Edge-Triggered D-Type Flip-Flops With Clear and Preset 14-SOIC -40 to 85 |
| 中文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO10 |
| 封裝： | 3 X 3 MM, PLASTIC, DFN-10 |
| 文件頁數： | 7/8頁 |
| 文件大?。?/td> | 208K |
| 代理商： | ISL6293-2CR |
Input Auto Selection
The charger selects only one power source to charge the
battery. When the CRDL input is higher than both the POR
threshold and the battery voltage, CRDL is the power
source. When this condition is not true, then the USB input is
selected as the power source. If the CRDL input happens to
have a voltage below the battery voltage but the USB input
has a voltage higher than the battery voltage, then the USB
input is used to charge the battery. The control circuit always
breaks both internal power devices before switching in one
power source to avoid any simultaneous conduction of both
power MOSFETs.
When the BAT pin voltage is below 1.7V, the charger selects
the CRDL input as the power source. Hence, if the USB
input is powered, the charger will not charge the battery.
USB Charge Current
When the USB port is the power source, the charge current
is programmed by the logic input USBP pin. When the USBP
is driven to logic LOW, the charge current is set to 90mA
(when R
IUSB
is 80k
). When the USBP is driven to logic
HIGH, the charge current is set to 450mA (when R
IUSB
is
80k
). The USBP is equivalent to a logic LOW when left
floating. Typically the P-channel MOSFET for the USB input
has an r
DS(ON)
of 700m
at room temperature. With a
500mA charge current, the typical head room is 350mV. If
the input voltage drops to a level that the voltage different
between the USB pin and the BAT pin is less than 350mV,
the r
DS(ON)
becomes a limiting factor of the charge current;
and the charge current will reduce to a lower level in this case.
Cradle Charge Current
The cradle charge current is programmed with the external
resistor connected between the ICDL pin and the GND pin.
The current can be calculated with the equation given in the
ICDL pin description. The typical P-channel MOSFET for the
CRDL input is 700m
at room temperature. The actual
charge current will be limited by several factors, for example,
the programmed ICDL, the thermal limit, and the r
DS(ON)
.
Floating Charge Voltage
The floating voltage during the constant voltage mode is
4.2V. The floating voltage has 1% accuracy over the ambient
temperature range of -40°C to 70°C. No leakage current
from any of the two power MOSFETs will cause the battery
voltage to drift to a higher level.
Trickle Charge Current
When the battery voltage is below the minimum battery
voltage V
MIN
given in the electrical specification, the charger
operates in a trickle/preconditioning mode. If power comes
from the cradle, the trickle mode current is
The trickle current is 45mA if the power comes from the USB
port with R
IUSB
= 80k
.
End-of-Charge Indication
The CHG pin outputs a logic HIGH by turning off the internal
open-drain MOSFET when the charge current falls below
8% of the constant current mode current for the cradle
charger or 10% for the USB charger. The charger, however,
does not turn off as long as an input power source is
attached.
Power Presence Indication
When either the USB or the cradle input voltage is above the
POR level, the PPR pin outputs a logic LOW signal to
indicate the presence of input power.
I
TRICKLE
R
ICDL
-----------------
100
=
A
( )
ISL6293
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6293-2CR-T | Dual Positive-Edge-Triggered D-Type Flip-Flops With Clear and Preset 14-PDIP -40 to 85 |
| ISL6293-2CRZ | Dual Positive-Edge-Triggered D-Type Flip-Flops With Clear and Preset 14-PDIP -40 to 85 |
| ISL6293-2CRZ-T | Dual Positive-Edge-Triggered D-Type Flip-Flops With Clear and Preset 14-SO -40 to 85 |
| ISL6296 | FlexiHash For Battery Authentication |
| ISL6296DH-T | FlexiHash For Battery Authentication |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6293-2CR-T | 功能描述:IC BATT CHRGR LI-ION 10-DFN RoHS:否 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:1 系列:- 功能:充電管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:3.75 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:剪切帶 (CT) 產品目錄頁面:669 (CN2011-ZH PDF) 其它名稱:MCP73831T-2ACI/OTCT |
| ISL6293-2CRZ | 功能描述:IC CHRGR LI-ION 28V/7V 3X3 10DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
| ISL6293-2CRZ-T | 功能描述:IC CHARGER LI-ION POLYMER 10-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
| ISL6293-2EVAL1 | 功能描述:EVALUATION BOARD ISL6293-2 RoHS:否 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:PCI Express® (PCIe) 主要目的:接口，收發器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要屬性:- 次要屬性:- 已供物品:板 |
| ISL6293-3CR | 制造商:Intersil Corporation 功能描述:CHGR LI-ION/LI-POL 300MAV TO 1A 4.2V 10DFN - Bulk |
發布緊急采購，3分鐘左右您將得到回復。