- 您現在的位置：買賣IC網 > PDF目錄384524 > ISL6293-2CR (INTERSIL CORP) Dual Positive-Edge-Triggered D-Type Flip-Flops With Clear and Preset 14-SOIC -40 to 85 PDF資料下載
參數資料
| 型號： | ISL6293-2CR |
| 廠商： | INTERSIL CORP |
| 元件分類： | 電源管理 |
| 英文描述： | Dual Positive-Edge-Triggered D-Type Flip-Flops With Clear and Preset 14-SOIC -40 to 85 |
| 中文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO10 |
| 封裝： | 3 X 3 MM, PLASTIC, DFN-10 |
| 文件頁數： | 6/8頁 |
| 文件大?。?/td> | 208K |
| 代理商： | ISL6293-2CR |
6
FN9180.0
EN (Pin 5)
Enable logic input. Connect to LOW or leave floating to
enable the charger.
IUSB (Pin 6)
The IUSB pin programs the USB charge current. This pin is
regulated to 0.8V. The current flowing out of this pin is
mirrored to the USB charge current control reference. When
the USBP pin is connected to logic HIGH, the typical USB
charge current can be found as:
The R
IUSB
has a programming range of 80k
to 103k
,
such that the USB current has a typical value ranges from
350mA to 450mA.
When the USBP pin is driven to logic LOW, the charge
current is approximately 1/5 of the above value.
USBP (Pin 7)
USB port selection logic input. When this pin is left floating or
driven to logic LOW, the USB port is regarded as a low-
power port, such that the charge current is 84mA. When this
pin is driven to logic HIGH, the USB port is considered a
high-power port, and the charge current is 450mA. The ratio
of the charge current when this pin is HIGH or LOW is fixed
at approximately 5:1.
GND (Pin 8)
System ground.
ICDL (Pin 9)
The ICDL pin has two functions. The first function is to
program the cradle charge current during the constant-
current mode. The voltage of this pin is 1.20V during the
constant-current mode of the cradle charger. The constant-
current mode current is programmed by the following
equation:
where R
ICDL
is the resistor connected to the ICDL pin (see
the Typical Application). The ratio is given by the following
table and curve.
It is recommended that the charge current be programmed
in the range of 300mA to 1A.
The second function of the ICDL pin is to monitor the actual
charge current. The voltage of this pin, V
ICDL
, is proportional
to the actual charge current, I
CHG
, in either the USB or the
cradle charger. When the cradle charger or the USB charger
is working with USBP connected to logic HIGH, the ICDL pin
voltage is given by the following equation.
where the ratio has the same value given in Table 1.
The cradle charge current should be programmed equal or
higher than the USB current; otherwise, the ICDL pin voltage
will be higher than 1.20V during the constant current mode
when the USB charger is working. The charger still works
properly but the accuracy of the current monitoring voltage
degrades and saturates at approximately 2.1V.
When the USB charger is working with the USBP pin
connected to logic LOW, the ICDL pin voltage is
approximately five times of the above equation.
BAT (Pin 10)
Charger output pin. Connect this pin to the battery pack or
the battery cell. A 1μF or larger value ceramic capacitor is
recommended for decoupling. The charger relies on the
battery for stability so a battery should always be connected
to the BAT pin.
Description
The ISL6293 is designed for a single-cell Li-ion or Li-polymer
battery charging circuit that accepts both a USB port and a
desktop cradle as its power source. The charge current from
each power source is independently programmable but only
one of the two sources charges the battery. The following
describes the operation of the charger.
TABLE 1. RATIO vs R
ICDL
R
ICDL
(k
)
1.5
2.2
3.0
3.9
4.6
Ratio
1291
1216
1155
1122
1088
I
USB
45000
V
R
IUSB
-----------------
45000
R
IUSB
-----------------
×
A
( )
=
=
I
CDL
ICDL
-----------------
ratio
=
A
( )
FIGURE 1. THE RATIO USED IN THE CHARGE CURRENT
CALCULATION vs R
ICDL
1280
1250
1220
1190
1160
1130
1100
1070
1
2
3
4
5
R
R
ICDL
(k
)
V
ICDL
CDL
---------------
I
CHG
R
I
------------------------------------
=
=
ISL6293
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6293-2CR-T | Dual Positive-Edge-Triggered D-Type Flip-Flops With Clear and Preset 14-PDIP -40 to 85 |
| ISL6293-2CRZ | Dual Positive-Edge-Triggered D-Type Flip-Flops With Clear and Preset 14-PDIP -40 to 85 |
| ISL6293-2CRZ-T | Dual Positive-Edge-Triggered D-Type Flip-Flops With Clear and Preset 14-SO -40 to 85 |
| ISL6296 | FlexiHash For Battery Authentication |
| ISL6296DH-T | FlexiHash For Battery Authentication |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6293-2CR-T | 功能描述:IC BATT CHRGR LI-ION 10-DFN RoHS:否 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:1 系列:- 功能:充電管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:3.75 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:剪切帶 (CT) 產品目錄頁面:669 (CN2011-ZH PDF) 其它名稱:MCP73831T-2ACI/OTCT |
| ISL6293-2CRZ | 功能描述:IC CHRGR LI-ION 28V/7V 3X3 10DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
| ISL6293-2CRZ-T | 功能描述:IC CHARGER LI-ION POLYMER 10-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
| ISL6293-2EVAL1 | 功能描述:EVALUATION BOARD ISL6293-2 RoHS:否 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:PCI Express® (PCIe) 主要目的:接口，收發器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要屬性:- 次要屬性:- 已供物品:板 |
| ISL6293-3CR | 制造商:Intersil Corporation 功能描述:CHGR LI-ION/LI-POL 300MAV TO 1A 4.2V 10DFN - Bulk |
發布緊急采購，3分鐘左右您將得到回復。