參數資料
型號: IRPLLNR3
廠商: International Rectifier
英文描述: Universal Input Linear Fluorescent Ballast using the IR2167
中文描述: 通用輸入線性熒光燈鎮流器用IR2167
文件頁數: 7/27頁
文件大?。?/td> 341K
代理商: IRPLLNR3
www.irf.com
7
RPLLNR3
The IR2167 Ballast Control IC is used to program the ballast operating points and protect the ballast
against conditions such as lamp strike failures, low DC bus, thermal overload or lamp failure during
normal operations. It is also used to regulate the DC bus and for power factor control allowing high
power factor and low harmonic distortion.
Power Factor Correction Section
The power factor correction section contained in the IR2167 forms the control for a boost topology
circuit operating in critical conduction mode. This topology is designed to step-up and regulate the
output DC bus voltage while drawing sinusoidal current from the line (low THD) which is “in phase”
with the AC input line voltage (HPF).
Ballast Control Section
The ballast control section of the IR2167 Ballast Control IC contains an oscillator, a high voltage half-
bridge gate driver and lamp fault protection circuitry. Please, refer to the datasheet of this IC for the
block diagram and the state diagram. Following is a breakdown of the operation of the ballast in all of
the different modes of operation. Please, refer to the AN: IRPLLNR2 for the ballast section design
(www.irf.com/Lighting).
Startup Mode
When power is initially applied to the ballast, the voltage on the VCC pin of the IR2167 begins to
charge up. The voltage for the IR2167 is derived from the current supplied from the rectified AC line
through startup resistor RSUPPLY. During this initial startup when the VCC voltage of the IR2167 is
below its rising under-voltage lock-out threshold (11.4V), it is in its UVLO and also its micro-power
mode. The micro-power mode of the IR2167 allows the use of a large value, low wattage startup
resistor (RSUPPLY). When the voltage on the IR2167 reaches the rising under-voltage lockout threshold,
the oscillator is enabled (this assumes that there are no fault conditions) and drives the half-bridge
output MOSFETs (MHS and MLS). When the half-bridge is oscillating, capacitor CSNUB, diodes
DCP1 and DCP2 form a snubber /charge pump circuit which limits the rise and fall time at the half-
bridge output and also supplies the current to charge capacitor CVCC2 to the VCC clamp voltage
(approx. 15.6V) of IR2167. When the rising under-voltage lockout threshold of the IR2167 is reached,
the PFC oscillator starts to oscillate and drive MOSFET MPFC to boost and regulate the bus voltage to
400 VDC. Oscillagraph of the start up of the VCC of the IR2167 DC is shown in figure 1.
相關PDF資料
PDF描述
IRPT1061A Power Module for 1 hp Motor Drives
IRPT3054A Power Module for 5 hp Motor Drives
IRPT5051C Integrated Power Stage for 15 hp Motor Drives
IRPT5051D Integrated Power Stage for 15 hp Motor Drives
IRPT5051E Integrated Power Stage for 15 hp Motor Drives
相關代理商/技術參數
參數描述
IRPLLNR4 功能描述:BALLAST UNIV INP FLUOR IR2166 RoHS:否 類別:編程器,開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 類型:MCU 適用于相關產品:Freescale MC68HC908LJ/LK(80-QFP ZIF 插口) 所含物品:面板、纜線、軟件、數據表和用戶手冊 其它名稱:520-1035
IRPLLNR5 功能描述:電源管理IC開發工具 Uni Inpt Lin Fluor Ballast 54W TL5 Lamp RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
IRPLLNR7 功能描述:電源管理IC開發工具 Flourescent Ballast Using IRS2166DPBF RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
IRPLMB1E 功能描述:KIT DESIGN BALLAST 220VAC RoHS:否 類別:編程器,開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 類型:MCU 適用于相關產品:Freescale MC68HC908LJ/LK(80-QFP ZIF 插口) 所含物品:面板、纜線、軟件、數據表和用戶手冊 其它名稱:520-1035
IR-POST-B 制造商:Knoll Systems 功能描述:Single Target IR Repeater Kit with Black Postage Stamp Receiver 制造商:KNOLL SYSTEMS 功能描述:IR REPEATER COMPLETE KIT BLACK POSTAGE STAMP RECEIVER