參數資料
型號： IRPLLNR3
廠商： International Rectifier
英文描述： Universal Input Linear Fluorescent Ballast using the IR2167
中文描述： 通用輸入線性熒光燈鎮流器用IR2167
文件頁數： 23/27頁
文件大小： 341K
代理商： IRPLLNR3
www.irf.com
23
RPLLNR3
Voltage mode Configuration Protection
Open cathode (one cathode disconnected completely) conditions are detected using the CS pin.
Open filament condition is detected in the lower cathode using the pin SD. In the case of open
filament in the upper cathode, the lamp preheats and ignites without causing over-current in the CS
pin, this is usually not a problem. However, we propose a circuit that has shutdown for open filament
as well using the SD pin (schematics of the whole circuit in the following page).
When the upper filament is connected, the transistor base is supplied with current via the 220K
resistor from the DC bus. This keeps it switched on at all times while the upper filament provides a DC
path. When the transistor is on the diode anode is held close to 0V so the SD pin is not affected by
this circuit and stays at 2V.
When the upper filament is open circuit, the transistor looses its base current and switches off so the
diode conducts and pulls the SD pin above the 5V threshold causing the system to shutdown. When
the lamp fails in this way and is replaced, the transistor will switch on and so the ballast will restart
without resetting the AC line.
Current mode configuration
The same PCB can be configured for current mode heating. It is needed to remove the Jumpers JV1
and JV2 and to introduce the Jumpers JC1 and JC2. It could be also usefull to add a resistor RDC in
parallel to CDC because in this configuration After initial start-up you could have some striations
(visible dark rings) on the lamps for a short period (a few minutes) particularly when the lamp has
been off for some time and is cold. The value should in the order of 100kOhm 0.5W.
We suggest the use of the Ballast Designer software to determine the values of the components to
use in this configuration.
相關PDF資料
PDF描述
IRPT1061A Power Module for 1 hp Motor Drives
IRPT3054A Power Module for 5 hp Motor Drives
IRPT5051C Integrated Power Stage for 15 hp Motor Drives
IRPT5051D Integrated Power Stage for 15 hp Motor Drives
IRPT5051E Integrated Power Stage for 15 hp Motor Drives
相關代理商/技術參數
參數描述
IRPLLNR4 功能描述:BALLAST UNIV INP FLUOR IR2166 RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 類型:MCU 適用于相關產品:Freescale MC68HC908LJ/LK（80-QFP ZIF 插口） 所含物品:面板、纜線、軟件、數據表和用戶手冊 其它名稱:520-1035
IRPLLNR5 功能描述:電源管理IC開發工具 Uni Inpt Lin Fluor Ballast 54W TL5 Lamp RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
IRPLLNR7 功能描述:電源管理IC開發工具 Flourescent Ballast Using IRS2166DPBF RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
IRPLMB1E 功能描述:KIT DESIGN BALLAST 220VAC RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 類型:MCU 適用于相關產品:Freescale MC68HC908LJ/LK（80-QFP ZIF 插口） 所含物品:面板、纜線、軟件、數據表和用戶手冊 其它名稱:520-1035
IR-POST-B 制造商:Knoll Systems 功能描述:Single Target IR Repeater Kit with Black Postage Stamp Receiver 制造商:KNOLL SYSTEMS 功能描述:IR REPEATER COMPLETE KIT BLACK POSTAGE STAMP RECEIVER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*