- 您現在的位置：買賣IC網 > PDF目錄384484 > IP82C50A-5 (HARRIS SEMICONDUCTOR) CMOS Asynchronous Communications Element PDF資料下載
參數資料
| 型號： | IP82C50A-5 |
| 廠商： | HARRIS SEMICONDUCTOR |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | CMOS Asynchronous Communications Element |
| 中文描述： | 1 CHANNEL(S), 625K bps, SERIAL COMM CONTROLLER, PDIP40 |
| 文件頁數： | 15/21頁 |
| 文件大?。?/td> | 101K |
| 代理商： | IP82C50A-5 |
15
Programming
The 82C50A is programmed by the control registers LCR,
lER, DLL and DLM, and MCR. These control words define
the character length, number of stop bits, parity, baud rate,
and modem interface.
While the control registers can be written in any order, the
lER should be written to last because it controls the interrupt
enables. Once the 82C50A is programmed and operational,
these registers can be updated any time the 82C50A is not
transmitting or receiving data.
The control signals required to access 82C50A internal reg-
isters are shown below.
Software Reset
A software reset of the 82C50A is a useful method for return-
ing to a completely known state without a system reset.
Such a reset consists of writing to the LCR, Divisor Latches,
and MCR registers. The LSR and RBR registers should be
read prior to enabling interrupts in order to clear out any
residual data or status bits which may be invalid for subse-
quent operation.
Crystal Operation
The 82C50A crystal oscillator circuitry is designed to oper-
ate with a fundamental mode, parallel resonant crystal. Table
8 shows the required crystal parameters and crystal circuit
configuration, respectively.
When using an external clock source, the XTAL1 input is
driven and the XTAL2 output is left open. Power
consumption when using an external clock is typically 50%
of that required when using a crystal. This is due to the
sinusoidal nature of the drive circuitry when using a crystal.
The maximum frequency of the 82C50A is 10MHz with an
external clock or a crystal attached to XTAL1 and XTAL2.
Using the external clock or crystal, and a divide by one
divisor, the maximum BAUDOUT is 10MHz, and the
maximum data rate is 625Kbps.
Out2
Master Reset
High
RTS
Master Reset
High
DTR
Master Reset
High
Out1
Master Reset
High
TABLE 7. 82C50A RESET OPERATIONS (Continued)
REGISTER/SIGNAL
RESET CONTROL
RESET
TABLE 8. TYPICAL CRYSTAL OSCILLATOR CIRCUIT
PARAMETER
Frequency
1.0 to 10MHz
Type of Operation
Parallel Resonant, Fundamental
Mode
Load Capacitance (CL)
20 or 32pF (Typ)
R
SERIES
(Max)
100
(f = 10MHz, CL = 32pF)
200
(f = 10MHz, CL = 20pF)
FIGURE 2. TYPICAL CRYSTAL OSCILLATOR CIRCUIT
CL
XTAL
XTAL1
XTAL2
TO
BAUD RATE
GENERATOR
LOGIC
PIN 17
PIN 16
RS
CL
82C50A
82C50A
相關PDF資料 |
PDF描述 |
|---|---|
| IP82C52 | CMOS Serial Controller Interface |
| IP82C55AZ | CMOS Programmable Peripheral Interface |
| IP82C82 | CMOS Octal Latching Bus Driver |
| IPB05N03LA | OptiMOS 2 Power-Transistor |
| IPB05N03L | OptiMOS Buck converter series |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IP82C52 | 功能描述:UART 接口集成電路 PERIPH UART/BRG 5V 16MHZ IND RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| IP82C52/+ | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:UART |
| IP82C54 | 功能描述:計時器和支持產品 PERIPH PRG-CNTR 5V 8MHZ 24PDIP IND RoHS:否 制造商:Micrel 類型:Standard 封裝 / 箱體:SOT-23 內部定時器數量:1 電源電壓-最大:18 V 電源電壓-最小:2.7 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Reel |
| IP82C54/+ | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog Timer Circuit |
| IP82C54-10 | 功能描述:計時器和支持產品 PERIPH PRG-CNTR 5V 10MHZ 24PDIP IND RoHS:否 制造商:Micrel 類型:Standard 封裝 / 箱體:SOT-23 內部定時器數量:1 電源電壓-最大:18 V 電源電壓-最小:2.7 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。