參數資料
型號： IDT82V2081PPG
廠商： IDT, Integrated Device Technology Inc
文件頁數： 16/68頁
文件大?。?/td> 0K
描述： IC LIU T1/J1/E1 1CH 44-TQFP
標準包裝： 80
類型： 線路接口裝置（LIU）
規程： T1/E1/J1
電源電壓： 3.13 V ~ 3.47 V
安裝類型： 表面貼裝
封裝/外殼： 44-LQFP
供應商設備封裝： 44-TQFP（10x10）
包裝： 托盤
其它名稱： 800-2347
82V2081PPG
IDT82V2081PPG-ND
23
INDUSTRIAL
TEMPERATURE RANGES
SINGLE CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
3.4.8
RECEIVE PATH SYSTEM INTERFACE
The receive path system interface consists of RCLK pin, RD/RDP pin
and RDN pin. In E1 mode, the RCLK outputs a recovered 2.048 MHz clock.
In T1/J1 mode, the RCLK outputs a recovered 1.544 MHz clock. The
received data is updated on the RD/RDP and RDN pins on the active edge
of RCLK. The active edge of RCLK can be selected by the RCLK_SEL bit
(RCF0, 0AH). And the active level of the data on RD/RDP and RDN can be
selected by the RD_INV bit (RCF0, 0AH).
In hardware control mode, only the active edge of RCLK can be
selected.IfRCLKEissettohigh,thefallingedgewillbechosenastheactive
edge of RCLK. If RCLKE is set to low, the rising edge will be chosen as the
active edge of RCLK. The active level of the data on RD/RDP and RDN is
the same as that in software control mode.
Thereceiveddatacanbeoutputtothesystemsideintwodifferentways:
Single Rail or Dual Rail, as selected by R_MD bit [1] (RCF0, 0AH). In Single
Rail mode, only RD pin is used to output data and the RDN/CV pin is used
to report the received errors. In Dual Rail Mode, both RDP pin and RDN pin
are used for outputting data.
In the receive Dual Rail mode, the CDR unit can be by-passed by setting
R_MD[1:0] to ‘11’ (binary). In this situation, the output data from the Data
Slicer will be output to the RDP/RDN pins directly, and the RCLK outputs
the exclusive OR (XOR) of the RDP and RDN. This is called receiver slicer
mode. In this case, the transmit path is still operating in Dual Rail mode.
3.4.9
RECEIVE PATH POWER DOWN
The receive path can be powered down by setting R_OFF bit (RCF0,
0AH) to‘1’.Inthiscase, the RCLK,RD/RDP,RDNandLOSwillbelogiclow.
In hardware control mode, receiverpower down can be selected by pull-
ing RPD pin to high. Refer to 5 HARDWARE CONTROL PIN SUMMARY
for more details.
3.5
JITTER ATTENUATOR
There is one Jitter Attenuator in the IDT82V2081. The Jitter Attenuator
can be deployed in the transmit path or the receive path, and can also be
disabled. This is selected by the JACF[1:0] bits (JACF, 04H).
In hardware control mode, Jitter Attenuator position, bandwidth and the
depth of FIFO can be selected by JA[1:0] pins. Refer to 5 HARDWARE
3.5.1
JITTER ATTENUATION FUNCTION DESCRIPTION
The Jitter Attenuator is composed of a FIFO and a DPLL, as shown in
Figure-11. The FIFO is used as a pool to buffer the jittered input data, then
the data is clocked out of the FIFO by a de-jittered clock. The depth of the
FIFO can be 32 bits, 64 bits or 128 bits, as selected by the JADP[1:0] bits
(JACF, 04H). In hardware control mode, the depth of FIFO can be selected
by JA[1:0] pins. Refer to 5 HARDWARE CONTROL PIN SUMMARY for
details. Consequently, the constant delay of the Jitter Attenuator will be 16
bits, 32 bits or 64 bits. Deeper FIFO can tolerate larger jitter, but at the cost
of increasing data latency time.
Figure-11 Jitter Attenuator
In E1 applications, the Corner Frequency of the DPLL can be 0.9 Hz or
6.8 Hz, as selected by the JABW bit (JACF, 04H). In T1/J1 applications,
the Corner Frequency of the DPLL can be 1.25 Hz or 5.00 Hz, as selected
bytheJABWbit(JACF,04H).ThelowertheCornerFrequencyis,thelonger
time is needed to achieve synchronization.
When the incoming data moves faster than the outgoing data, the FIFO
will overflow. This overflow is captured by the JAOV_IS bit (INTS1, 1AH).
If the incoming data moves slower than the outgoing data, the FIFO will
underflow. This underflow is captured by the JAUD_IS bit (INTS1, 1AH). For
some applications that are sensitive to data corruption, the JA limit mode
can be enabled by setting JA_LIMIT bit (JACF, 04H) to ‘1’. In the JA limit
mode, the speed of the outgoing data will be adjusted automatically when
theFIFOisclosetoitsfulloremptiness.Thecriteriaofstartingspeedadjust-
ment are shown in Table-16. The JA limit mode can reduce the possibility
of FIFO overflow and underflow, but the quality of jitter attenuation is dete-
riorated.
3.5.2
JITTER ATTENUATOR PERFORMANCE
The performance of the Jitter Attenuator in the IDT82V2081 meets the
ITU-T I.431, G.703, G.736-739, G.823, G.824, ETSI 300011, ETSI TBR12/
13, AT&T TR62411 specifications. Details of the Jitter Attenuator perfor-
Table-16 Criteria of Starting Speed Adjustment
FIFO Depth
Criteria for Adjusting Data Outgoing Speed
32 Bits
2 bits close to its full or emptiness
64 Bits
3 bits close to its full or emptiness
128 Bits
4 bits close to its full or emptiness
FIFO
32/64/128
DPLL
Jittered Data
De-jittered Data
Jittered Clock
De-jittered Clock
MCLK
W
R
RCLK
RD/RDP
RDN
相關PDF資料
PDF描述
TLC0834CD IC 8-BIT SERIAL OUT A/D 14-SOIC
IDT82V2081PP IC LIU T1/J1/E1 1CH 44-TQFP
VI-26K-CV-B1 CONVERTER MOD DC/DC 40V 150W
VI-26J-IW CONVERTER MOD DC/DC 36V 100W
VI-26J-CV-B1 CONVERTER MOD DC/DC 36V 150W
相關代理商/技術參數
參數描述
IDT82V2081PPG8 功能描述:IC LIU T1/J1/E1 1CH 44-TQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:250 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR)
IDT82V2082 制造商:IDT 制造商全稱:Integrated Device Technology 功能描述:DUAL CHANNEL T1/E1/J1 LONG HAUL/ SHORT HAUL LINE INTERFACE UNIT
IDT82V2082_09 制造商:IDT 制造商全稱:Integrated Device Technology 功能描述:DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
IDT82V2082BFBLANK 制造商:IDT 制造商全稱:Integrated Device Technology 功能描述:DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
IDT82V2082BFG 功能描述:IC LIU T1/E1/J1 2CH 81BGA RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:250 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR)
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*