- 您現在的位置：買賣IC網 > PDF目錄1923 > ICS1893AFILF (IDT, Integrated Device Technology Inc)PHYCEIVER LOW PWR 3.3V 48-SSOP PDF資料下載
參數資料
| 型號： | ICS1893AFILF |
| 廠商： | IDT, Integrated Device Technology Inc |
| 文件頁數： | 79/136頁 |
| 文件大?。?/td> | 0K |
| 描述： | PHYCEIVER LOW PWR 3.3V 48-SSOP |
| 標準包裝： | 30 |
| 系列： | PHYceiver™ |
| 類型： | PHY 收發器 |
| 規程： | MII |
| 電源電壓： | 3.14 V ~ 3.47 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-BSSOP（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 48-SSOP |
| 包裝： | 管件 |
| 其它名稱： | 1893AFILF |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁當前第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁
Chapter 7
Functional Blocks
ICS1893AF, Rev. D 10/26/04
October, 2004
47
ICS1893AF Data Sheet - Release
Copyright 2004, Integrated Circuit Systems, Inc.
All rights reserved.
7.5
Functional Block: 10Base-T Operations
When configured for 10Base-T mode, the ICS1893AF MAC/Repeater Interface can be configured to
provide either a 10M MII (Media Independent Interface) or a 10M Serial Interface. The Twisted-Pair
Interface is automatically configured to provide a two-level, Manchester-encoded signal at the voltage
levels specified in the ISO/IEC standard. (For more information on the Twisted-Pair Interface, see Section
The 10Base-T and 100Base-TX operations differ as follows. 10Base-T operations are fundamentally
simpler than 100Base-TX operations. The data rate is slower, requiring less encoding than 100Base-TX
operations. In addition, the bandwidth requirements (and therefore the line attenuation issues) are not as
severe as with 100-MHz operations. Consequently, when an ICS1893AF is set for 10Base-T operations, it
requires fewer internal circuits in contrast to 100Base-TX operations. (For an overview of 10Base-T
operations, see Section 5.6, “10Base-T Operations”.).
7.5.1
10Base-T Operation: Manchester Encoder/Decoder
During data transmission the ICS1893AF acquires data from its MAC/Repeater Interface in either 4-bit
nibbles or as a serial bit stream. The ICS1893AF converts this data into a Manchester-encoded signal for
presentation to its MDI, as required by the ISO/IEC specification.
In a Manchester-encoded signal, all logic:
Ones are:
– Positive during the first half of the bit period
– Negative during the second half of the bit period
Zeros are:
– Negative during the first half of the bit period
– Positive during the second half of the bit period
During 10Base-T data reception, a Manchester Decoder translates the serial bit stream obtained from the
Twisted-Pair Receiver (MDI) into an NRZ bit stream. The Manchester Decoder then passes the data to the
MAC/Repeater Interface in either serial or parallel format, depending on the interface configuration.
Manchester-encoded signals have the following advantages:
Every bit period has an encoded clock.
The split-phase nature of the signal always provides a zero DC level regardless of the data (that is, there
is no baseline wander phenomenon).
The primary disadvantage in using Manchester-encoded signals is that it doubles the data rate, making it
operationally prohibitive for 100-MHz operations.
7.5.2
10Base-T Operation: Clock Synthesis
The ICS1893AF synthesizes the clocks required for synchronizing data transmission. In 10Base-T mode,
the MAC Interface provides a 10M MII (Media Independent Interface):
10M MII interface, the ICS1893AF synthesizes a 2.5-MHz clock for nibble-wide transactions
7.5.3
10Base-T Operation: Clock Recovery
The ICS1893AF recovers its receive clock from the Manchester-encoded data stream obtained from its
Twisted-Pair Receiver using a phase-locked loop (PLL). The ICS1893AF then uses this recovered clock for
synchronizing data transmission between itself and the MAC. Receive-clock PLL acquisitions begin with
reception of the MAC Frame Preamble and continue as long as the ICS1893AF is receiving data.
相關PDF資料 |
PDF描述 |
|---|---|
| ICS1893BFILF | PHYCEIVER LOW PWR 3.3V 48-SSOP |
| ICS1894KI-32LF | PHYCEIVER LOW PWR 3.3V 32QFN |
| ICS1894KI-40LFT | PHYCEIVER LOW PWR 3.3V 40QFN |
| ID82C55A | IC I/O EXPANDER 24B 40DIP |
| ID82C82 | IC DRIVER BUS OCT LATCHING 20DIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ICS1893AFILFT | 功能描述:PHYCEIVER LOW PWR 3.3V 48-SSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:PHYceiver™ 標準包裝:250 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
| ICS1893AFIT | 功能描述:PHYCEIVER LOW PWR 3.3V 48-SSOP RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:PHYceiver™ 標準包裝:1,000 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) |
| ICS1893AFLF | 功能描述:PHYCEIVER LOW PWR 3.3V 48-SSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:PHYceiver™ 標準包裝:1 系列:- 類型:收發器 驅動器/接收器數:1/1 規程:RS422，RS485 電源電壓:4.5 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SOICN 包裝:剪切帶 (CT) 其它名稱:ISL31470EIBZ-T7ACT |
| ICS1893AFLFT | 功能描述:PHYCEIVER LOW PWR 3.3V 48-SSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:PHYceiver™ 標準包裝:250 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
| ICS1893AFT | 功能描述:PHYCEIVER LOW PWR 3.3V 48-SSOP RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:PHYceiver™ 標準包裝:1,000 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。