- 您現在的位置：買賣IC網 > PDF目錄383084 > ICL7107S (Intersil Corporation) LED Display, A/D Converters(3 1/2 位LED 顯示器驅動 A/D轉換器) PDF資料下載
參數資料
| 型號： | ICL7107S |
| 廠商： | Intersil Corporation |
| 元件分類： | 串行ADC |
| 英文描述： | LED Display, A/D Converters(3 1/2 位LED 顯示器驅動 A/D轉換器) |
| 中文描述： | LED顯示，A / D轉換（3 1 / 2位發光顯示器驅動的A / D轉換器） |
| 文件頁數： | 7/16頁 |
| 文件大?。?/td> | 534K |
| 代理商： | ICL7107S |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁
7
FN3082.8
Analog COMMON
This pin is included primarily to set the common mode
voltage for battery operation (ICL7106) or for any system
where the input signals are floating with respect to the power
supply. The COMMON pin sets a voltage that is
approximately 2.8V more negative than the positive supply.
This is selected to give a minimum end-of-life battery voltage
of about 6V. However, analog COMMON has some of the
attributes of a reference voltage. When the total supply
voltage is large enough to cause the zener to regulate (>7V),
the COMMON voltage will have a low voltage coefficient
(0.001%/V), low output impedance (
15
), and a
temperature coefficient typically less than 80ppm/×
o
C.
The limitations of the on chip reference should also be
recognized, however. With the ICL7107, the internal heating
which results from the LED drivers can cause some
degradation in performance. Due to their higher thermal
resistance, plastic parts are poorer in this respect than
ceramic. The combination of reference Temperature
Coefficient (TC), internal chip dissipation, and package
thermal resistance can increase noise near full scale from
25
μ
V to 80
μ
V
P-P
. Also the linearity in going from a high
dissipation count such as 1000 (20 segments on) to a low
dissipation count such as 1111(8 segments on) can suffer by
a count or more. Devices with a positive TC reference may
require several counts to pull out of an over-range condition.
This is because over-range is a low dissipation mode, with the
three least significant digits blanked. Similarly, units with a
negative TC may cycle between over-range and a non-over-
range count as the die alternately heats and cools. All these
problems are of course eliminated if an external reference is
used.
The ICL7106, with its negligible dissipation, suffers from
none of these problems. In either case, an external reference
can easily be added, as shown in Figure 4.
Analog COMMON is also used as the input low return during
auto-zero and de-integrate. If IN LO is different from analog
COMMON, a common mode voltage exists in the system
and is taken care of by the excellent CMRR of the converter.
However, in some applications IN LO will be set at a fixed
known voltage (power supply common for instance). In this
application, analog COMMON should be tied to the same
point, thus removing the common mode voltage from the
converter. The same holds true for the reference voltage. If
reference can be conveniently tied to analog COMMON, it
should be since this removes the common mode voltage
from the reference system.
Within the lC, analog COMMON is tied to an N-Channel FET
that can sink approximately 30mA of current to hold the
voltage 2.8V below the positive supply (when a load is trying
to pull the common line positive). However, there is only
10
μ
A of source current, so COMMON may easily be tied to a
more negative voltage thus overriding the internal reference.
TEST
The TEST pin serves two functions. On the ICL7106 it is
coupled to the internally generated digital supply through a
500
resistor. Thus it can be used as the negative supply for
externally generated segment drivers such as decimal points
or any other presentation the user may want to include on
the LCD display. Figures 5 and 6 show such an application.
No more than a 1mA load should be applied.
The second function is a “l(fā)amp test”. When TEST is pulled
high (to V+) all segments will be turned on and the display
should read “1888”. The TEST pin will sink about 15mA
under these conditions.
CAUTION: In the lamp test mode, the segments have a constant DC
voltage (no square-wave). This may burn the LCD display if main-
tained for extended periods.
FIGURE 4A.
FIGURE 4B.
FIGURE 4. USING AN EXTERNAL REFERENCE
ICL7106
ICL7107
V
REF LO
REF HI
V+
V-
6.8V
ZENER
I
Z
ICL7106
ICL7107
V
REF HI
REF LO
COMMON
V+
ICL8069
1.2V
REFERENCE
6.8k
20k
ICL7106
V+
BP
TEST
21
37
TO LCD
BACKPLANE
TO LCD
DECIMAL
POINT
1M
FIGURE 5. SIMPLE INVERTER FOR FIXED DECIMAL POINT
ICL7106, ICL7107, ICL7107S
相關PDF資料 |
PDF描述 |
|---|---|
| ICL7106S | LCDDisplay, A/D Converters(3 1/2 位驅動LCD顯示器的A/D轉換器) |
| ICL7106 | LCD Display, A/D Converters(3 1/2 位驅動LCD顯示器的A/D轉換器) |
| ICL7107 | LED Display, A/D Converters(3 1/2 位LED 顯示器驅動 A/D轉換器) |
| ICL7109IJL | 12 Bit A/D Converter With 3-State Binary Outputs |
| ICL7109CPL | Dual LVDS Receiver 5-SOT-23 -40 to 85 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ICL7107SCPL | 功能描述:IC ADC 3.5 DIGIT LED 40-DIP RoHS:否 類別:集成電路 (IC) >> PMIC - 顯示器驅動器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 顯示器類型:真空熒光 (VF) 配置:5 x 7（矩陣） 接口:串行 數字或字符:- 電流 - 電源:3.5mA 電源電壓:2.7 V ~ 3.6 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:16-SSOP（0.154"，3.90mm 寬） 供應商設備封裝:16-QSOP 包裝:帶卷 (TR) |
| ICL7107SCPLZ | 功能描述:LED顯示驅動器 ADC 3 5 DIG LED DRVR COM RoHS:否 制造商:Micrel 數位數量:5 片段數量: 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-44 工作電源電壓:4.75 V to 11 V 最大電源電流:10 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Tube |
| ICL7109 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:N-CHANNEL JFET |
| ICL7109 WAF | 制造商:Harris Corporation 功能描述: |
| ICL71091DL | 制造商:Harris Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。