- 您現在的位置：買賣IC網 > PDF目錄383084 > ICL7107S (Intersil Corporation) LED Display, A/D Converters(3 1/2 位LED 顯示器驅動 A/D轉換器) PDF資料下載
參數資料
| 型號： | ICL7107S |
| 廠商： | Intersil Corporation |
| 元件分類： | 串行ADC |
| 英文描述： | LED Display, A/D Converters(3 1/2 位LED 顯示器驅動 A/D轉換器) |
| 中文描述： | LED顯示，A / D轉換（3 1 / 2位發光顯示器驅動的A / D轉換器） |
| 文件頁數： | 6/16頁 |
| 文件大?。?/td> | 534K |
| 代理商： | ICL7107S |
6
FN3082.8
Detailed Description
Analog Section
Figure 3 shows the Analog Section for the ICL7106 and
ICL7107. Each measurement cycle is divided into three
phases. They are (1) auto-zero (A-Z), (2) signal integrate
(INT) and (3) de-integrate (DE).
Auto-Zero Phase
During auto-zero three things happen. First, input high and low
are disconnected from the pins and internally shorted to analog
COMMON. Second, the reference capacitor is charged to the
reference voltage. Third, a feedback loop is closed around the
system to charge the auto-zero capacitor C
AZ
to compensate
for offset voltages in the buffer amplifier, integrator, and
comparator. Since the comparator is included in the loop, the A-
Z accuracy is limited only by the noise of the system. In any
case, the offset referred to the input is less than 10
μ
V.
Signal Integrate Phase
During signal integrate, the auto-zero loop is opened, the
internal short is removed, and the internal input high and low
are connected to the external pins. The converter then
integrates the differential voltage between IN HI and IN LO for a
fixed time. This differential voltage can be within a wide
common mode range: up to 1V from either supply. If, on the
other hand, the input signal has no return with respect to the
converter power supply, IN LO can be tied to analog COMMON
to establish the correct common mode voltage. At the end of
this phase, the polarity of the integrated signal is determined.
De-Integrate Phase
The final phase is de-integrate, or reference integrate. Input
low is internally connected to analog COMMON and input
high is connected across the previously charged reference
capacitor. Circuitry within the chip ensures that the capacitor
will be connected with the correct polarity to cause the
integrator output to return to zero. The time required for the
output to return to zero is proportional to the input signal.
Specifically the digital reading displayed is:
.
Differential Input
The input can accept differential voltages anywhere within the
common mode range of the input amplifier, or specifically from
0.5V below the positive supply to 1V above the negative
supply. In this range, the system has a CMRR of 86dB typical.
However, care must be exercised to assure the integrator
output does not saturate. A worst case condition would be a
large positive common mode voltage with a near full scale
negative differential input voltage. The negative input signal
drives the integrator positive when most of its swing has been
used up by the positive common mode voltage. For these
critical applications the integrator output swing can be
reduced to less than the recommended 2V full scale swing
with little loss of accuracy. The integrator output can swing to
within 0.3V of either supply without loss of linearity.
Differential Reference
The reference voltage can be generated anywhere within the
power supply voltage of the converter. The main source of
common mode error is a roll-over voltage caused by the
reference capacitor losing or gaining charge to stray capacity
on its nodes. If there is a large common mode voltage, the
reference capacitor can gain charge (increase voltage) when
called up to de-integrate a positive signal but lose charge
(decrease voltage) when called up to de-integrate a negative
input signal. This difference in reference for positive or negative
input voltage will give a roll-over error. However, by selecting the
reference capacitor such that it is large enough in comparison
to the stray capacitance, this error can be held to less than 0.5
count worst case. (See Component Value Selection.)
DISPLAY COUNT = 1000
V
REF
--------------
FIGURE 3. ANALOG SECTION OF ICL7106 AND ICL7107
DE
-
DE+
C
INT
INT
C
AZ
A-Z
R
INT
BUFFER
-
+
A-Z
COMPARATOR
IN HI
COMMON
IN LO
31
32
30
DE-
DE+
INT
A-Z
34
C
REF
+
36
REF HI
C
REF
REF LO
35
A-Z
A-Z
33
C
REF
-
28
29
27
TO
DIGITAL
SECTION
A-Z AND DE
(±)
INTEGRATOR
INT
STRAY
STRAY
V+
10
μ
A
V-
N
INPUT
HIGH
2.8V
6.2V
V+
1
INPUT
LOW
-
+
-
+
-
+
ICL7106, ICL7107, ICL7107S
相關PDF資料 |
PDF描述 |
|---|---|
| ICL7106S | LCDDisplay, A/D Converters(3 1/2 位驅動LCD顯示器的A/D轉換器) |
| ICL7106 | LCD Display, A/D Converters(3 1/2 位驅動LCD顯示器的A/D轉換器) |
| ICL7107 | LED Display, A/D Converters(3 1/2 位LED 顯示器驅動 A/D轉換器) |
| ICL7109IJL | 12 Bit A/D Converter With 3-State Binary Outputs |
| ICL7109CPL | Dual LVDS Receiver 5-SOT-23 -40 to 85 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ICL7107SCPL | 功能描述:IC ADC 3.5 DIGIT LED 40-DIP RoHS:否 類別:集成電路 (IC) >> PMIC - 顯示器驅動器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 顯示器類型:真空熒光 (VF) 配置:5 x 7（矩陣） 接口:串行 數字或字符:- 電流 - 電源:3.5mA 電源電壓:2.7 V ~ 3.6 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:16-SSOP（0.154"，3.90mm 寬） 供應商設備封裝:16-QSOP 包裝:帶卷 (TR) |
| ICL7107SCPLZ | 功能描述:LED顯示驅動器 ADC 3 5 DIG LED DRVR COM RoHS:否 制造商:Micrel 數位數量:5 片段數量: 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-44 工作電源電壓:4.75 V to 11 V 最大電源電流:10 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Tube |
| ICL7109 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:N-CHANNEL JFET |
| ICL7109 WAF | 制造商:Harris Corporation 功能描述: |
| ICL71091DL | 制造商:Harris Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。