- 您現在的位置：買賣IC網 > PDF目錄370661 > HPC3130PBKLOW-PROFILEQUAD (Texas Instruments, Inc.) PCI HOT PLUG CONTROLLER PDF資料下載
參數資料
| 型號： | HPC3130PBKLOW-PROFILEQUAD |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | PCI HOT PLUG CONTROLLER |
| 中文描述： | 的PCI熱插拔控制器 |
| 文件頁數： | 21/40頁 |
| 文件大小： | 555K |
| 代理商： | HPC3130PBKLOW-PROFILEQUAD |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
HPC3130
PCI HOT PLUG CONTROLLER
SCPS029B – DECEMBER1998
21
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
IDLEREQ, IDLEGNT, FRAME, and IRDY pins are not connected in manual mode. In contrast, during automatic
connection, the HPC3130 requests the PCIBus to make sure it is idle before it sequences through the
connection sequence.
In manual mode, software has to perform each part of the connection sequence. Figure 9 is an example of the
manual connection sequence. There could be several other ways to implement this protocol.
PCI_CLK
PWRON/OFF
PWRGOOD
SLOTRST
CLKON
REQ64ON
SLOTREQ64
BUS_CTL
BUSON
Figure 9. Manual Connection Sequencing
disconnecting sequence
The HPC3130 provides two mechanisms to isolate a PCI slot from the PCI bus so an add–in card can be
removed. One of the mechanisms is called manual sequencing and is enabled by default. This mechanism
allows the software to control the entire disconnect sequence. This means it is the software’s responsibility to
remove a powered slot from the PCI bus without any impact to the system.
The second mechanism is called auto sequencing and can be enabled by programming either Auto-Sequence
1 or Auto-Sequence 2 in the general configuration register.Unlike the connection sequence, which has two
different auto-connection sequencing modes, the autodisconnect sequence has only one mode of operation.
The steps in the auto-disconnect sequence are as follows:
1.
Software may assert SLOTRST to the appropriate slot by writing a 0 to the SLOTRST_O bit in the hot-plug
control register. This is optional.
2.
Next the software must set the BUS_CTL bit in the hot-plug control register to a 1.
3.
Once the BUS_CTL bit is set to a 1, the HPC3130 asserts IDLEREQ.
4.
Once IDLEGNT is asserted and FRAME and IRDY are deasserted, the HPC3130 deasserts BUSON and
CLKON and asserts REQ64ON to isolate the slot from the PCI bus.
5.
The HPC3130 then drives PWRON/OFF low to power off the slot.
相關PDF資料 |
PDF描述 |
|---|---|
| HPC43100VHG30 | 16-Bit Microcontroller |
| HPC46003E20 | 16-Bit Microcontroller |
| HPC46003L20 | 16-Bit Microcontroller |
| HPC46003L30 | 16-Bit Microcontroller |
| HPC46003T20 | 16-Bit Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HPC3130PBM | 功能描述:外圍驅動器與原件 - PCI HOT PLUG CONTROLLER RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| HPC3130PBMQUADFLAT | 制造商:TI 制造商全稱:Texas Instruments 功能描述:PCI HOT PLUG CONTROLLER |
| HPC3130PGE | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:PCI Bus Interface/Controller |
| HPC3130PGELOW-PROFILEQUAD | 制造商:TI 制造商全稱:Texas Instruments 功能描述:PCI HOT PLUG CONTROLLER |
| HPC36003 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:High-Performance microControllers |
發布緊急采購，3分鐘左右您將得到回復。