- 您現在的位置：買賣IC網 > PDF目錄384423 > HIP9010AB (INTERSIL CORP) Engine Knock Signal Processor PDF資料下載
參數資料
| 型號： | HIP9010AB |
| 廠商： | INTERSIL CORP |
| 元件分類： | 模擬信號調理 |
| 英文描述： | Engine Knock Signal Processor |
| 中文描述： | SPECIALTY ANALOG CIRCUIT, PDSO20 |
| 封裝： | PLASTIC, MS-013AC, SOIC-20 |
| 文件頁數： | 5/12頁 |
| 文件大?。?/td> | 81K |
| 代理商： | HIP9010AB |
4-5
+5V
HIP9010
MICROPROCESSOR
SPI BUS
C3, 0.022
μ
F
C2, 3.3nF
C1, 3.3nF
R1
R4
R3
4MHz
A/D
CONVERTER
V
DD
V
MID
GND
S1IN
S1FB
S0IN
S0FB
OSCIN
OSCOUT
INTOUT
MOSI
MISO
SCK
CS
INT/HOLD
TEST
TRANSDUCERS
R2
FIGURE 2. SIMPLIFIED BLOCK DIAGRAM OF THE HIP9010 IN AN AUTOMOTIVE APPLICATION
20pF
20pF
1M
Pin Descriptions
PIN
NUMBER
SYMBOL
DESCRIPTION
1
V
DD
5V power input.
2
GND
This terminal is tied to ground.
3
V
MID
This terminal is tied to the internal mid-supply generator and is brought out for supply bypassing by a 0.022
μ
F
capacitor.
4
INTOUT
Buffered output of the integrator.
5 and 6
NC
These terminals are not internally connected. DO NOT USE.
7
INT/HOLD
Selects whether the chip is in the Integrate Mode (Input High) or in the Hold Mode (Input Low).
8
CS
A low input on this pin enables the chip to communicate over the SPI bus.
9
OSCIN
Input to inverter used for the oscillator circuit. A 4MHz crystal or ceramic resonator is connected between this
pin and pin 10. To bias the inverter, a 1.0M
to 10M
resistor is usually connected between this pin and pin 10.
10
OSCOUT
Output of the inverter used for the oscillator. See pin 9 above.
11
MISO
Output of the chip SPI data bus. It is the inversion of the chip DATAIN line. This is an open drain output. The
output must be disabled by placing the CS High when the chip is not selected.
12
MOSI
Input of the chip SPI data bus. Data length is eight bits.
13
SCK
Input from the SPI clock. Normally high, the data is clocked to the chip internal circuitry on the rising clock edge.
14
TEST
A low on this pin places the chip in the test mode. For normal operation this terminal is tied high or left open.
15 and 16
NC
These terminals are not internally connected. DO NOT USE.
17
S1IN
Inverting input to sensor one amplifier. A resistor is tied from this summing input to the transducer. A second
resistor is tied between this terminal and terminal 18, S1FB to establish the gain of the amplifier.
18
S1FB
Output of the sensor one amplifier. This terminal is used to apply feedback.
19
S0FB
Output of the sensor zero amplifier. This terminal is used to apply feedback.
20
S0IN
Inverting input to sensor zero amplifier. A resistor is tied from this summing input to the transducer. A second
resistor is tied between this terminal and terminal 19, S0FB to establish the gain of the amplifier.
HIP9010
相關PDF資料 |
PDF描述 |
|---|---|
| HIP9011ABZ | Engine Knock Signal Processor |
| HIP9011 | Engine Knock Signal Processor |
| HIP9011AB | Engine Knock Signal Processor |
| HIP9020 | Programmable Quad Buffer with Pre and Post Scaler Dividers |
| HIP9020AB | Programmable Quad Buffer with Pre and Post Scaler Dividers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HIP9011 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Engine Knock Signal Processor |
| HIP9011_06 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Engine Knock Signal Processor |
| HIP9011AB | 功能描述:IC SENSOR ENGINE KNOCK 20-SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
| HIP9011ABR4682 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| HIP9011ABR4745 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
發布緊急采購，3分鐘左右您將得到回復。