- 您現在的位置：買賣IC網 > PDF目錄384423 > HIP9010AB (INTERSIL CORP) Engine Knock Signal Processor PDF資料下載
參數資料
| 型號： | HIP9010AB |
| 廠商： | INTERSIL CORP |
| 元件分類： | 模擬信號調理 |
| 英文描述： | Engine Knock Signal Processor |
| 中文描述： | SPECIALTY ANALOG CIRCUIT, PDSO20 |
| 封裝： | PLASTIC, MS-013AC, SOIC-20 |
| 文件頁數： | 11/12頁 |
| 文件大?。?/td> | 81K |
| 代理商： | HIP9010AB |
4-11
Test Multiplexer
This circuit receives the positive and negative outputs out of
the two integrators, together with the outputs from different
parts of the chip. The output is controlled by the fifth
programming word of the communications protocol. This
multiplexes the switch capacitor filter output, the gain control
output as well as the antialias output.
Differential to Single-ended Converter
This signal takes the output of the two integrators (through
the test multiplexer circuit) and provides a signal that is the
sum of the two signals. This technique is used to improve the
noise immunity of the system.
Output Buffer
This output amplifier is the same as the input amplifier used
to interface to the sensors. For test purposes when we look
at the output of the antialias filter, the input amplifiers are in
the power down mode.
TABLE 4. INTERGRATE/HOLD TIMING REQUIREMENTS
DESCRIPTION
UNITS
T1 maximum rise time of the INT/HOLD signal.
45ns
T2 maximum time after INT/HOLD rises for the INOUT to
begin to intergrate.
20
μ
s
T3 maximum fall time of INT/HOLD signal.
45ns
T4 typical time after INT/HOLD goes low before chip
goes into hold state.
20
μ
s
T5 minimum INT/HOLD time during power up sequence.
1
μ
s
CS
INT/HOLD
FIGURE 7. POWER UP SEQUENCE
INT/HOLD
INTOUT
T1
T2
T3
T4
FIGURE 8. INTEGRATOR TIMING
HIP9010
相關PDF資料 |
PDF描述 |
|---|---|
| HIP9011ABZ | Engine Knock Signal Processor |
| HIP9011 | Engine Knock Signal Processor |
| HIP9011AB | Engine Knock Signal Processor |
| HIP9020 | Programmable Quad Buffer with Pre and Post Scaler Dividers |
| HIP9020AB | Programmable Quad Buffer with Pre and Post Scaler Dividers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HIP9011 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Engine Knock Signal Processor |
| HIP9011_06 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Engine Knock Signal Processor |
| HIP9011AB | 功能描述:IC SENSOR ENGINE KNOCK 20-SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
| HIP9011ABR4682 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| HIP9011ABR4745 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
發布緊急采購，3分鐘左右您將得到回復。