參數資料
型號： HIP6021CB
廠商： HARRIS SEMICONDUCTOR
元件分類： 穩壓器
英文描述： Advanced PWM and Triple Linear Power Controller
中文描述： SWITCHING CONTROLLER, 215 kHz SWITCHING FREQ-MAX, PDSO28
文件頁數： 7/16頁
文件大?。?/td> 186K
代理商： HIP6021CB
7
error amplifier. Similarly, the COMP pin is the error amplifier
output. These pins are used to compensate the voltage-mode
control feedback loop of the synchronous PWM converter.
VSEN1 (Pin 22)
This pin is connected to the PWM converter’s output voltage.
The PGOOD and OVP comparator circuits use this signal to
report output voltage status and for over-voltage protection.
DRIVE2 (Pin 1)
Connect this pin to the gate of an external MOSFET. This pin
provides the drive for the AGP regulator’s pass transistor.
VSEN2 (Pin 10)
Connect this pin to the output of the AGP linear regulator.
The voltage at this pin is regulated to the level
predetermined by the logic-level status of the SELECT pin.
This pin is also monitored for under-voltage events.
SELECT (Pin 11)
This pin determines the output voltage of the AGP bus linear
regulator. A low TTL input sets the output voltage to 1.5V
and the linear controller regulates this voltage to within
±
3%.
A TTL high input turns Q3 on continuously, providing a DC
current path from the input (+3.3V
IN
) to the output (V
OUT2
)
of the AGP controller.
DRIVE3 (Pin 18)
Connect this pin to the gate of an external MOSFET. This pin
provides the drive for the 1.5V regulator’s pass transistor.
VSEN3 (Pin 19)
Connect this pin to the output of the 1.5V linear regulator.
This pin is monitored for under-voltage events.
DRIVE4 (Pin 15)
Connect this pin to the gate of an external MOSFET. This pin
provides the drive for the 1.8V regulator’s pass transistor.
VSEN4 (Pin 14)
Connect this pin to the output of the linear 1.8V regulator.
This pin is monitored for under voltage events.
Description
Operation
The HIP6021A monitors and precisely controls 4 output
voltage levels (Refer to Block and Simplified Power System
Diagrams, and Typical Application Schematic). It is designed
for microprocessor computer applications with 3.3V, 5V,
and 12V bias input from an ATX power supply. The
microprocessor core voltage (V
OUT1
) is controlled in a
synchronous-rectified buck converter configuration. The
PWM controller regulates the microprocessor core voltage
to a level programmed by the 5-bit digital-to-analog
converter (DAC).
The AGP bus voltage (VOUT2) is set using the SELECT pin
to either a 1.5V linear regulated output or to the 3.3V
IN
through a pass device. Selection of either output voltage is
set depending on the logic level of the SELECT pin.
The two remaining linear controllers supply the 1.5V GTL
bus power (V
OUT3
) and the 1.8V memory power (V
OUT4
).
These output voltages are user adjustable. All linear
controllers are designed to employ an external pass
transistor.
Initialization
The HIP6021A automatically initializes upon receipt of input
power. Special sequencing of the input supplies is not
necessary. The Power-On Reset (POR) function continually
monitors the input supply voltages. The POR monitors the
bias voltage (+12V
IN
) at the VCC pin, the 5V input voltage
(+5V
IN
) on the OCSET pin, and the 3.3V input voltage
(+3.3V
IN
) at the VAUX pin. The normal level on OCSET is
equal to +5V
IN
less a fixed voltage drop (see over-current
protection). The POR function initiates soft-start operation
after all supply voltages exceed their POR thresholds.
Soft-Start
The POR function initiates the soft-start sequence. Initially,
the voltage on the SS pin rapidly increases to approximately
1V (this minimizes the softstart interval). Then an internal
28
μ
A current source charges an external capacitor (C
SS
) on
the SS pin to 4.5V. The PWM error amplifier reference input
(+ terminal) and output (COMP pin) are clamped to a level
proportional to the SS pin voltage. As the SS pin voltage
slews from 1V to 4V, the output clamp allows generation of
PHASE pulses of increasing width that charge the output
capacitor(s). After the output voltage increases to
approximately 70% of the set value, the reference input
clamp slows the output voltage rate-of-rise and provides a
smooth transition to the final set voltage. Additionally, all
linear regulators’ reference inputs are clamped to a voltage
proportional to the SS pin voltage. This method provides a
rapid and controlled output voltage rise.
Figure 2 shows the soft-start sequence for the typical
application. At T0 the SS voltage rapidly increases to
approximately 1V. At T1, the SS pin and error amplifier
output voltage reach the valley of the oscillator’s triangle
wave. The oscillator’s triangular waveform is compared to
the clamped error amplifier output voltage. As the SS pin
voltage increases, the pulse width on the PHASE pin
increases. The interval of increasing pulse width continues
until each output reaches sufficient voltage to transfer
control to the input reference clamp. If we consider the 2.5V
core output (V
OUT1
) in Figure 2, this time occurs at T2.
During the interval between T2 and T3, the error amplifier
reference ramps to the final value and the converter
regulates the output a voltage proportional to the SS pin
voltage. At T3 the input clamp voltage exceeds the
reference voltage and the output voltage is in regulation.
HIP6021A
相關PDF資料
PDF描述
HIP6021 100000 SYSTEM GATE 1.8 VOLT FPGA - NOT RECOMMENDED for NEW DESIGN
HIP6021A 100000 SYSTEM GATE 1.8 VOLT FPGA - NOT RECOMMENDED for NEW DESIGN
HIP6021EVAL1 Advanced PWM and Triple Linear Power Controller
HIP6302CB-T Microprocessor CORE Voltage Regulator Multi-Phase Buck PWM Controller
HIP6302 Microprocessor CORE Voltage Regulator Multi-Phase Buck PWM Controller(微處理器核心多相脈寬調制解調器)
相關代理商/技術參數
參數描述
HIP6021CB-T 功能描述:IC REG QD BCK/LINEAR 28-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 + 切換式 系列:- 標準包裝:2,500 系列:- 拓?fù)?降壓（降壓）同步（3），線性（LDO）（2） 功能:任何功能 輸出數:5 頻率 - 開關:300kHz 電壓/電流 - 輸出 1:控制器 電壓/電流 - 輸出 2:控制器 電壓/電流 - 輸出 3:控制器 帶 LED 驅動器:無 帶監控器:無 帶序列發生器:是 電源電壓:5.6 V ~ 24 V 工作溫度:-40°C ~ 85°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:*
HIP6021CBZ 功能描述:電壓模式 PWM 控制器 SINGLE PWM & TRPL LINEAR CNTRLR RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel
HIP6021CBZ-T 功能描述:電壓模式 PWM 控制器 SINGLE PWM & TRPL LINEAR CNTRLR RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel
HIP6021EVAL1 功能描述:電源管理IC開發工具 HIP6021 EVAL BRD RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
HIP6028 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Advanced PWM and Dual Linear Power Control with Integrated ACPI Support Interface
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*