- 您現在的位置：買賣IC網 > PDF目錄383058 > HIP1012CB (INTERSIL CORP) 512 MACROCELL 3.3 VOLT ZERO POWER ISP CP - NOT RECOMMENDED for NEW DESIGN PDF資料下載
參數資料
| 型號： | HIP1012CB |
| 廠商： | INTERSIL CORP |
| 元件分類： | 電源管理 |
| 英文描述： | 512 MACROCELL 3.3 VOLT ZERO POWER ISP CP - NOT RECOMMENDED for NEW DESIGN |
| 中文描述： | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO14 |
| 封裝： | PLASTIC, MS-012AB, SOIC-14 |
| 文件頁數： | 1/15頁 |
| 文件大?。?/td> | 173K |
| 代理商： | HIP1012CB |
1
File Number
4419.4
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 321-724-7143
|
Copyright
Intersil Corporation 1999
Hot Plug is a trademark of Core International, Inc.
HIP1012, HIP1012A
Dual Power Distribution Controller
The HIP1012 is a HOT SWAP dual supply power distribution
controller. Two external N-Channel MOSFETs are driven to
distribute power while providing load fault isolation.
At turn-on, the gate of each external N-Channel MOSFET is
charged with a 10
μ
A current source. Capacitors on each
gate (see the Typical Application Diagram), create a
programmable ramp (soft turn-on) to control inrush currents.
A built in charge pump supplies the gate drive for the 12V
supply N-Channel MOSFET switch.
Over current protection is facilitated by two external current
sense resistors. When the current through either resistor
exceeds the user programmed value the controller enters the
current regulation mode. The time-out capacitor, C
TIM
, starts
charging as the controller enters the time out period. Once
C
TIM
charges to a 2V threshold, the N-Channel MOSFETs
are latched off. In the event of a fault at least three times the
current limit level, the N-Channel MOSFET gates are pulled
low immediately before entering time out period. The
controller is reset by a rising edge on either PWRON pin.
Choosing the voltage selection mode the HIP1012 controls
either +12V/5V or +3.3V/+5V supplies.
For those applications where voltage tolerance is a concern
the HIP1012A has a minimum nominal over current threshold
voltage of 50mV as compared to 100mV for the HIP1012.
Ordering Information
Features
HOT SWAP Dual Power Distribution Control for +5V and
+12V or +5V and +3.3V
Provides Fault Isolation
Programmable Current Regulation Level
Programmable Time Out
Charge Pump Allows the Use of N-Channel MOSFETs
Power Good and Over Current Latch Indicators
Enhanced Over Current Sensitivity Available
Redundant Power On Controls
Adjustable Turn-On Ramp
Protection During Turn-On
Two Levels of Current Limit Detection Provide Fast
Response to Varying Fault Conditions
Less Than 1
μ
s Response Time to Dead Short
3
μ
s Response Time to 200% Current Overshoot
Applications
Redundant Array of Independent Disks (RAID) System
Power Distribution Control
Hot Plug, Hot Swap Components
PART NUMBER
TEMP.
RANGE (
o
C)
PACKAGE
PKG.
NO.
HIP1012CB
HIP1012ACB
-0 to 70
14 Ld SOIC
M14.15
HIP1012CB-T
HIP1012ACB-T
-0 to 70
14 Ld SOIC
Tape and Reel
M14.15
Pinout
HIP1012 (SOIC)
TOP VIEW
Typical Application Diagram
8
9
10
11
12
14
13
7
6
5
4
3
2
1
3/12VS
3/12VG
V
DD
PWRON2
5VG
5VS
3/12VISEN
GND
C
PUMP
C
TIM
PGOOD
R
ILIM
5VISEN
MODE/
PWRON1
3/12VS
3/12VG
V
DD
M/PON1
PWRON2
5VG
5VS
PGOOD
3/12VISEN
R
ILIM
GND
C
TIM
C
PUMP
5ISEN
HIP1012
12V
R
LOAD
R
ILIM
C
TIM
POWER ON
INPUTS
C
PUMP
R
SENSE
5V
R
LOAD
R
SENSE
5V OR 3.3V
OPTIONAL
R
FILTER
C
FILTER
V
DD
R
GATE
C
GATE
C
GATE
R
GATE
Data Sheet
November 1999
相關PDF資料 |
PDF描述 |
|---|---|
| HIP1012ACB-T | Dual Power Distribution Controller |
| HIP1030AS | 1A High Side Driver with Overload Protection |
| HIP1030 | 1A High Side Driver with Overload Protection(帶超載保護的1A高邊驅動器) |
| HIP6005CB | Buck Pulse-Width Modulator (PWM) Controller and Output Voltage Monitor |
| HIP6005 | Buck Pulse-Width Modulator (PWM) Controller and Output Voltage Monitor(脈沖帶寬調節控制和輸出電壓檢測電路) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HIP1012CB-T | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Dual Power Distribution Controller |
| HIP1012EVAL1 | 功能描述:電源管理IC開發工具 GENERIC EVAL BRD RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| HIP1012EVAL2 | 功能描述:電源管理IC開發工具 RAID EVALUATION BRD RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| HIP1013 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Low Cost Dual Power Distribution Controller |
| HIP1013_04 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Low Cost Dual Power Distribution Controller |
發布緊急采購，3分鐘左右您將得到回復。