- 您現在的位置：買賣IC網 > PDF目錄383057 > HFA1130883 (Intersil Corporation) Output Clamping, 850MHz Current Feedback Amplifier PDF資料下載
參數資料
| 型號： | HFA1130883 |
| 廠商： | Intersil Corporation |
| 英文描述： | Output Clamping, 850MHz Current Feedback Amplifier |
| 中文描述： | 輸出鉗位，850MHz的電流反饋放大器 |
| 文件頁數： | 17/19頁 |
| 文件大?。?/td> | 865K |
| 代理商： | HFA1130883 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁
DESIGN INFORMATION
(Continued)
The information contained in this section has been developed through characterization by Intersil Semiconductor and is for use as
application and design information only. No guarantee is implied.
220
HFA1130
When the output is clamped, the negative input continues to
source a slewing current (I
CLAMP
put to the quiescent voltage defined by the input. QP5 must
sink this current while clamping, because the -IN current is
always mirrored onto the high impedance node. The clamping
current is calculated as:
I
CLAMP
= (V
-IN
- V
OUT CLAMPED
) / R
F
+ V
-IN
/ R
G
.
As an example, a unity gain circuit with V
IN
= 2V, V
H
= 1V, and
R
F
= 510
would have I
CLAMP
= (2V - 1V) / 510
+ 2V /
∞
=
1.96mA. Note that Icc will increase by I
CLAMP
when the output
is clamp limited.
Clamp Accuracy
The clamped output voltage will not be exactly equal to the
voltage applied to V
H
or V
L
Offset errors, mostly due to V
BE
mismatches, necessitate a clamp accuracy parameter which
is found in the device specifications. Clamp accuracy is a
function of the clamping conditions. Referring again to Figure
3, it can be seen that one component of clamp accuracy is the
V
BE
mismatch between the QX6 transistors, and the QX5
transistors. If the transistors always ran at the same current
level there would be no V
BE
mismatch, and no contribution to
the inaccuracy. The QX6 transistors are biased at a constant
current, but as described earlier, the current through QX5 is
equivalent to I
CLAMP
. V
BE
increases as I
CLAMP
increases,
causing the clamped output voltage to increase as well.
I
CLAMP
is a function of the overdrive level (A
VCL
x V
IN
- V
OUT
CLAMPED
) and R
F
, so clamp accuracy degrades as the over-
drive increases, and as R
F
decreases. As an example, the
specified accuracy of
±
60mV for a 2X overdrive with
R
F
=510
degrades to
±
220mV for R
F
=240
at the same
overdrive, or to ±
±
250mV for a 3X overdrive with R
F
= 510
.
Consideration must also be given to the fact that the clamp
voltages have an effect on amplifier linearity. The “Nonlinear-
ity Near Clamp Voltage” curve in the data sheet illustrates the
impact of several clamp levels on linearity.
Clamp Range
Unlike some competitor devices, both V
H
and V
L
have usable
ranges that cross 0V. While V
H
must be more positive than
V
L
, both may be positive or negative, within the range restric-
tions indicated in the specifications. For example, the
HFA1130 could be limited to ECL output levels by setting V
H
= -0.8V and V
L
= -1.8V. V
H
and V
L
may be connected to the
same voltage (GND for instance) but the result won’t be in a
DC output voltage from an AC input signal. A 150mV - 200mV
AC signal will still be present at the output.
Recovery from Overdrive
The output voltage remains at the clamp level as long as the
overdrive condition remains. When the input voltage drops
below the overdrive level (V
CLAMP
/ A
VCL
) the amplifier will
return to linear operation. A time delay, known as the Over-
drive Recovery Time, is required for this resumption of linear
operation. The plots of “Unclamped Performance” and
“Clamped Performance” highlight the HFA1130’s subnano-
second recovery time. The difference between the
unclamped and clamped propagation delays is the overdrive
recovery time. The appropriate propagation delays are 4.0ns
for the unclamped pulse, and 4.8ns for the clamped (2X
overdrive) pulse yielding an overdrive recovery time of
800ps. The measurement uses the 90% point of the output
transition to ensure that linear operation has resumed. Note:
The propagation delay illustrated is dominated by the fixtur-
ing. The delta shown is accurate, but the true HFA1130
propagation delay is 500ps.
Spec Number
511082-883
相關PDF資料 |
PDF描述 |
|---|---|
| HFA1130IB | CAPACITOR 1500UF 200V ELECT TSUP |
| HFA1130IP | 850MHz, Output Limiting, Low Distortion Current Feedback Operational Amplifier |
| HFA1130EVAL | 850MHz, Output Limiting, Low Distortion Current Feedback Operational Amplifier |
| HGTD1N120BNS | 5.3A, 1200V, NPT Series N-Channel IGBT |
| HGTD1N120CNS | 6.2A, 1200V, NPT Series N-Channel IGBT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HFA1130EVAL | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:850MHz, Output Limiting, Low Distortion Current Feedback Operational Amplifier |
| HFA1130IB | 功能描述:運算放大器 - 運放 800 MHz Output Limit RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| HFA1130IB96 | 功能描述:IC BUFFER CFA 850MHZ 8-SOIC RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:50 系列:LinCMOS™ 放大器類型:通用 電路數:4 輸出類型:- 轉換速率:0.05 V/µs 增益帶寬積:110kHz -3db帶寬:- 電流 - 輸入偏壓:0.7pA 電壓 - 輸入偏移:210µV 電流 - 電源:57µA 電流 - 輸出 / 通道:30mA 電壓 - 電源，單路/雙路(±):3 V ~ 16 V，±1.5 V ~ 8 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SOIC 包裝:管件 產品目錄頁面:865 (CN2011-ZH PDF) 其它名稱:296-1834296-1834-5 |
| HFA1130IBZ | 功能描述:運算放大器 - 運放 W/ANL OPAMP 850MHZ CFB CLMP IND RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| HFA1130IBZ | 制造商:Intersil Corporation 功能描述:Operational Amplifier (Op-Amp) IC |
發布緊急采購，3分鐘左右您將得到回復。