- 您現在的位置：買賣IC網 > PDF目錄370458 > HD4043612 (Hitachi,Ltd.) 4-bit HMCS400-Series microcomputer(4位單片微計算機) PDF資料下載
參數資料
| 型號： | HD4043612 |
| 廠商： | Hitachi,Ltd. |
| 英文描述： | 4-bit HMCS400-Series microcomputer(4位單片微計算機) |
| 中文描述： | 4位HMCS400系列微機（4位單片微計算機） |
| 文件頁數： | 75/115頁 |
| 文件大?。?/td> | 710K |
| 代理商： | HD4043612 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁當前第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁
HD404369 Series
75
The output level of the SO pin is invalid until the first data is output after MCU reset, or until the output
level control in idle states is performed.
Transfer Control:
The serial interface is activated by the STS instruction. The octal counter is reset to 000
by this instruction, and it increments at the rising edge of the transmit clock. When the eighth transmit
clock signal is input or when serial transmission/receive is discontinued, the octal counter is reset to 000,
the serial interrupt request flag (IFS: $003, bit 2) is set, and the transfer stops.
When the prescaler output is selected as the transmit clock, the transmit clock frequency is selected as 4t
cyc
to 8192t
cyc
by setting bits 0 to 2 (SMR0– SMR2) of serial mode register (SMR: $005) and bit 0 (PMRC0)
of port mode register C (PMRC: $025) as listed in table 28.
Operating States:
The serial interface has the following operating states; transitions between them are
shown in figure 59.
STS wait state
Transmit clock wait state
Transfer state
Continuous clock output state (only in internal clock mode)
STS wait state: The serial interface enters STS wait state by MCU reset (00, 10 in figure 59). In STS
wait state, the serial interface is initialized and the transmit clock is ignored. If the STS instruction is
then executed (01, 11), the serial interface enters transmit clock wait state.
Transmit clock wait state: Transmit clock wait state is the period between the STS execution and the
falling edge of the first transmit clock. In transmit clock wait state, input of the transmit clock (02, 12)
increments the octal counter, shifts the serial data register, and puts the serial interface in transfer state.
However, note that if continuous clock output mode is selected in internal clock mode, the serial
interface does not enter transfer state but enters continuous clock output state (17).
The serial interface enters STS wait state by writing data to the serial mode register (SMR: $005) (04,
14) in transmit clock wait state.
Transfer state: Transfer state is the period between the falling edge of the first clock and the rising edge
of the eighth clock. In transfer state, the input of eight clocks or the execution of the STS instruction
sets the octal counter to 000, and the serial interface enters another state. When the STS instruction is
executed (05, 15), transmit clock wait state is entered. When eight clocks are input, transmit clock wait
state is entered (03) in external clock mode, and STS wait state is entered (13) in internal clock mode. In
internal clock mode, the transmit clock stops after outputting eight clocks.
In transfer state, writing data to the serial mode register (SMR: $005) (06, 16) initializes the serial
interface, and STS wait state is entered.
If the state changes from transfer to another state, the serial interrupt request flag (IFS: $003, bit 2) is set
by the octal counter that is reset to 000.
Continuous clock output state (only in internal clock mode): Continuous clock output state is entered
only in internal clock mode. In this state, the serial interface does not transmit/receive data but only
outputs the transmit clock from the
SCK
pin.
相關PDF資料 |
PDF描述 |
|---|---|
| HD404369 | 4-bit HMCS400-Series microcomputer |
| HD404369H | 4-bit HMCS400-Series microcomputer |
| HD404369S | 4-bit HMCS400-Series microcomputer |
| HD404369F | 4-bit HMCS400-Series microcomputer |
| HD404372 | Low-Voltage AS Microcomputers with On-Chip A/D Converter(帶片上A/D轉換器的低壓微計算機) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HD4043612F | 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:4-bit HMCS400-Series microcomputer |
| HD4043612H | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:microcomputer has an A/D converter |
| HD4043612S | 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:4-bit HMCS400-Series microcomputer |
| HD404364 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:HMCS43XXFamily User＇s Manual/Device |
| HD404364F | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:microcomputer has an A/D converter |
發布緊急采購，3分鐘左右您將得到回復。